Count copper already on the board as connections already made

Fixed tracks and vias only kept other nets away, so a pin fanned out to
its plane was routed to the plane again, beside its own fan-out. Pins,
zones and planes that fixed copper of their net touches now form one
connected group: a fanned-out supply pin needs nothing more, a fanned-out
signal routes from its via, and copper touching no pin or zone adds
nothing to route.

bench/bench.py

@@ -24,9 +24,11 @@ off. Exits non-zero if any run crashed or timed out.
 from __future__ import annotations
 
 import argparse
+from concurrent.futures import ThreadPoolExecutor, as_completed
 import json
 import math
 import os
+from pathlib import Path
 import re
 import shlex
 import subprocess
@@ -34,8 +36,6 @@ import sys
 import tempfile
 import threading
 import time
-from concurrent.futures import ThreadPoolExecutor, as_completed
-from pathlib import Path
 
 NOT_ROUTED = re.compile(r"freeroute: (\d+) connection\(s\) not routed")
 TO_ZONE = re.compile(r"freeroute: (\d+) more connection\(s\) left to a zone fill")

bench/diagnose.py

@@ -0,0 +1,296 @@
+"""Why did each connection fail? Sort the failures of one exact-engine run.
+
+    uv run python bench/diagnose.py board.dsn --edge-clearance 0.5 [--json out.json]
+
+Every connection the exact engine leaves unrouted lands in one bucket:
+
+rejected    the grid routed it, the exact geometry check refused its copper
+alone       it cannot be routed even on a board with no other routes: the
+            pads, keepouts or the grid itself are the limit, not congestion
+walled-in   in the routed board one of its pins has no way out: a flood from
+            the pin's end cells through free cells stops short (pin access)
+congestion  both pins can get out, but no free path joins them
+
+The board state is the one the result came from (the best pass), rebuilt by
+replaying that pass's paths. Diagnostic only: it reaches into the router.
+"""
+
+from __future__ import annotations
+
+import argparse
+from collections import Counter
+import json
+from pathlib import Path
+import sys
+
+from freeroute.board import build_board
+from freeroute.board.search_tree import ShapeSearchTree
+from freeroute.dsn import parse_dsn
+from freeroute.geometry.octagon import overlaps_2d
+from freeroute.route import grid_router
+from freeroute.route.exact_router import route_board_exact
+from freeroute.route.grid_router import GridRouter, _ends_of
+from freeroute.route.pipeline import (
+    _mm_to_board,
+    _rule_clearance_dsn,
+    _rule_width_dsn,
+    _via_half_board,
+)
+
+# a pin whose free neighbourhood holds fewer nodes than this is walled in
+FLOOD_LIMIT = 200
+
+
+def _capture_router():
+    """Patch GridRouter so the instance route_board_exact builds, and the paths
+    of its best pass, can be read back afterwards."""
+    seen: dict = {}
+    original_commit = GridRouter._commit
+    original_snapshot = GridRouter._snapshot
+
+    def commit(self, conn, path):
+        original_commit(self, conn, path)
+        self._diag_paths[conn.index] = (list(path), conn.a_end, conn.b_end)
+
+    def snapshot(self, conns):
+        self._diag_best = {c.index: self._diag_paths[c.index] for c in conns if c.routed}
+        seen["router"] = self
+        return original_snapshot(self, conns)
+
+    def init(self, *args, **kwargs):
+        original_init(self, *args, **kwargs)
+        self._diag_paths = {}
+        self._diag_best = {}
+        seen["kwargs"] = kwargs
+        seen["args"] = args
+
+    original_init = GridRouter.__init__
+    GridRouter.__init__ = init
+    GridRouter._commit = commit
+    GridRouter._snapshot = snapshot
+    return seen
+
+
+def _capture_conflicts() -> list:
+    """Record each exact-check refusal: the copper box, its kind, and the
+    shape it came too close to. The check stops at a connection's first
+    conflict, so refusals and rejected connections line up in order."""
+    log: list = []
+    original = ShapeSearchTree.clearance_conflict
+
+    def conflict(self, box, net_no, layer, clearance, kind="wire"):
+        hit = original(self, box, net_no, layer, clearance, kind)
+        if hit:
+            # the shape that tripped the check, found the way the check does
+            other = None
+            expanded = box.offset(clearance)
+            for s in self.overlapping(expanded):
+                if s.net_no == net_no or not s.on_layer(layer):
+                    continue
+                if s.blocks != "all" and s.blocks != kind + "s":
+                    continue
+                if not s.clearance:
+                    if s.tile.overlaps(box):
+                        other = s
+                        break
+                    continue
+                if (s.exact is not None and overlaps_2d(s.exact, expanded)) or (
+                    s.exact is None and s.tile.overlaps(expanded)
+                ):
+                    other = s
+                    break
+            log.append((net_no, kind, layer, box, clearance, other))
+        return hit
+
+    ShapeSearchTree.clearance_conflict = conflict
+    return log
+
+
+def _wall_name(wall, names) -> str:
+    if isinstance(wall, str):
+        if wall.startswith("fixed copper of net "):
+            net = int(wall.rsplit(" ", 1)[1])
+            return f"fixed copper of {names.get(net, net)}"
+        return wall
+    return names.get(wall, "pads/keepouts")
+
+
+def _gap(a, b) -> int:
+    dx = max(b.ll.x - a.ur.x, a.ll.x - b.ur.x, 0)
+    dy = max(b.ll.y - a.ur.y, a.ll.y - b.ur.y, 0)
+    return max(dx, dy)
+
+
+def _fresh(seen) -> GridRouter:
+    router = grid_router.GridRouter(*seen["args"], **seen["kwargs"])
+    router._conns = router._build_connections()
+    return router
+
+
+def _static_wall(router: GridRouter, node) -> str:
+    """What static copper closes a node: a keepout, copper already on the
+    board (a fixed via or track, by net), or a pad."""
+    if node in router._keepout:
+        return "keepout"
+    fixed = getattr(router, "_diag_fixed", None)
+    if fixed is None:
+        fixed = router._diag_fixed = {}
+        margin = router.clearance + router.half_width
+        for net, layers, box in router.board.get_fixed_copper():
+            for cell in router._cells_in_box(box, margin):
+                for layer in layers:
+                    fixed[(*cell, layer)] = net
+    net = fixed.get(node)
+    if net is not None:
+        return f"fixed copper of net {net}"
+    return "pads"
+
+
+def _flood(router: GridRouter, pin, net_no: int, conns) -> tuple[int, Counter]:
+    """How many nodes a pin can reach through free cells (up to FLOOD_LIMIT),
+    and which other nets' copper bounds the region."""
+    walls: Counter = Counter()
+    # the search starts on every end node unconditionally (it may leave one
+    # inside a wire keepout by a via), so the flood does too
+    start = list(router._end_nodes(pin, net_no, conns))
+    seen = set(start)
+    frontier = list(start)
+    while frontier and len(seen) < FLOOD_LIMIT:
+        x, y, layer = frontier.pop()
+        steps = [(x + dx, y + dy, layer) for dx, dy in router._neighbours]
+        if router._via_placeable((x, y), net_no, conns):
+            steps += [(x, y, other) for other in router.layers if other != layer]
+        elif len(seen) == 1:
+            # the pin's own exit is a via that other copper leaves no room for
+            via_nodes = [(*c, lay) for c in router._via_cells((x, y)) for lay in router.layers]
+            for owner in router._crossed_owners(via_nodes, net_no, conns):
+                walls[conns[owner].net_no] += 1
+        for n in steps:
+            if n in seen or not (0 <= n[0] < router.cols and 0 <= n[1] < router.rows):
+                continue
+            if router._enter_cost(n[:2], n[2], net_no, False, conns) is None:
+                # trace, via footprint or clearance halo, as rip-up sees them
+                owners = router._crossed_owners([n], net_no, conns)
+                for owner in owners:
+                    walls[conns[owner].net_no] += 1
+                if not owners:
+                    walls[_static_wall(router, n)] += 1
+                continue
+            seen.add(n)
+            frontier.append(n)
+    return len(seen), walls
+
+
+def diagnose(
+    dsn_text: str, edge_clearance_mm: float | None, resolution: int = 2, shove: bool = False,
+    access_cost: float = 0.0,
+) -> dict:
+    dsn = parse_dsn(dsn_text)
+    names = {i + 1: n.name for i, n in enumerate(dsn.nets)}
+    scale = max(dsn.resolution.value, 1)
+    seen = _capture_router()
+    conflicts = _capture_conflicts()
+    exact = route_board_exact(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * scale),
+        clearance=round(_rule_clearance_dsn(dsn) * scale),
+        via_half=_via_half_board(dsn, scale),
+        edge_clearance=_mm_to_board(dsn, scale, edge_clearance_mm),
+        resolution=resolution,
+        shove=shove,
+        access_cost=access_cost,
+    )
+    routed = seen["router"]
+    best = routed._diag_best
+    grid_failed = {(c.net_no, *_ends_of(c)) for c in routed._conns if c.index not in best}
+
+    # the board as the best pass left it
+    state = _fresh(seen)
+    conns = state._conns
+    for idx, (path, a_end, b_end) in best.items():
+        conns[idx].a_end, conns[idx].b_end = a_end, b_end
+        state._commit(conns[idx], path)
+    empty = _fresh(seen)
+    # refusals in the order the check made them, one per rejected connection
+    per_net: dict[int, list] = {}
+    for net_no, kind, layer, box, clearance, other in conflicts:
+        if other is None:
+            what = "?"
+        elif other.net_no == -1:
+            what = "keepout" if other.clearance else "rule area"
+        else:
+            what = ("trace/via of " if other.routed else "pad of ") + names.get(other.net_no, "?")
+        need = clearance if other is None or other.clearance else 0
+        short = (need - _gap(box, other.tile)) / scale / 1000 if other is not None else 0
+        per_net.setdefault(net_no, []).append(
+            {"copper": kind, "layer": layer, "against": what, "short_mm": round(short, 4)}
+        )
+    by_key = {(c.net_no, *_ends_of(c)): c for c in conns}
+
+    rows = []
+    for failure in exact.result.failed:
+        net_no, a, b = failure[0], failure[1], failure[2]
+        zone = failure[3] if len(failure) > 3 else ""
+        if zone:
+            continue  # left to a zone fill, not a failure
+        key = (net_no, a, b)
+        row = {"net": names.get(net_no, str(net_no)), "a": a, "b": b}
+        conn = by_key.get(key)
+        if key not in grid_failed:
+            row["kind"] = "rejected"
+            if per_net.get(net_no):
+                row["conflict"] = per_net[net_no].pop(0)
+        elif conn is None:
+            row["kind"] = "unknown"
+        elif empty._search(empty._conns[conn.index], allow_ripup=False, conns=empty._conns) is None:
+            row["kind"] = "alone"
+        else:
+            walled = []
+            for end, group in ((a, conn.a_group), (b, conn.b_group)):
+                for pin in group[0][:1]:  # a group's first pin is its route end
+                    reach, walls = _flood(state, pin, net_no, conns)
+                    if reach < FLOOD_LIMIT:
+                        walled.append({
+                            "pin": end, "reach": reach,
+                            "walls": [
+                                _wall_name(n, names) for n, _ in walls.most_common(4)
+                            ],
+                        })
+            row["kind"] = "walled-in" if walled else "congestion"
+            if walled:
+                row["walled"] = walled
+        rows.append(row)
+    return {"failures": rows, "counts": dict(Counter(r["kind"] for r in rows))}
+
+
+def main(argv: list[str] | None = None) -> int:
+    ap = argparse.ArgumentParser(description=__doc__.split("\n\n")[0])
+    ap.add_argument("dsn", type=Path)
+    ap.add_argument("--edge-clearance", type=float, metavar="MM")
+    ap.add_argument("--grid-resolution", type=int, default=2, metavar="K")
+    ap.add_argument("--shove", action="store_true", help="as mckicad routes")
+    ap.add_argument("--access-cost", type=float, default=0.0)
+    ap.add_argument("--json", type=Path, help="also write the full table here")
+    args = ap.parse_args(argv)
+
+    report = diagnose(args.dsn.read_text(), args.edge_clearance, args.grid_resolution, args.shove,
+                      args.access_cost)
+    for row in report["failures"]:
+        extra = ""
+        for w in row.get("walled", []):
+            extra += f"  [{w['pin']} reaches {w['reach']} cells, walled by {', '.join(w['walls'])}]"
+        if "conflict" in row:
+            c = row["conflict"]
+            extra += (f"  [{c['copper']} on layer {c['layer']} {c['short_mm']} mm too close"
+                      f" to {c['against']}]")
+        print(f"{row['kind']:11} {row['net']}: {row['a']} to {row['b']}{extra}")
+    total = sum(report["counts"].values())
+    print(f"\n{total} failed: " + ", ".join(f"{k} {v}" for k, v in sorted(report["counts"].items())),
+          file=sys.stderr)
+    if args.json:
+        args.json.write_text(json.dumps(report, indent=1))
+    return 0
+
+
+if __name__ == "__main__":
+    raise SystemExit(main())

src/freeroute/board/board.py

@@ -70,6 +70,27 @@ class BasicBoard:
     def get_traces(self) -> list[Trace]:
         return [it for it in self._items if isinstance(it, Trace)]
 
+    def get_fixed_copper(self) -> list[tuple[int, frozenset[int], IntBox]]:
+        """Copper already routed on the board (the DSN's ``wiring``), as
+        ``(net, layers, box)``. A track is its segments, its corners and the
+        round caps at its ends (as squares); a via is its largest pad."""
+        from freeroute.geometry.polyline import Polyline, PolylineShape, corner_box
+
+        out: list[tuple[int, frozenset[int], IntBox]] = []
+        for item in self._items:
+            if not item.fixed or not item.net_nos:
+                continue
+            net = item.net_nos[0]
+            if isinstance(item, Trace) and not item.is_empty():
+                layers = frozenset({item.layer})
+                for box in PolylineShape(Polyline(item.corners), item.half_width).tiles():
+                    out.append((net, layers, box))
+                for end in (item.corners[0], item.corners[-1]):
+                    out.append((net, layers, corner_box(end, item.half_width)))
+            elif isinstance(item, Via) and item.shape is not None:
+                out.append((net, frozenset(item.layers), item.shape.bounding_box()))
+        return out
+
     def get_vias(self) -> list[Via]:
         return [it for it in self._items if isinstance(it, Via)]
 

src/freeroute/board/build.py

@@ -31,7 +31,7 @@ from freeroute.geometry.polygon_shape import PolygonShape
 
 from .board import BasicBoard
 from .clearance import ClearanceMatrix
-from .items import ConductionArea, ObstacleArea, Pin
+from .items import ConductionArea, ObstacleArea, Pin, Trace, Via
 from .layer import Layer, LayerStructure
 from .net import Nets
 from .transform import CoordinateTransform
@@ -56,6 +56,7 @@ def build_board(dsn: DsnBoard) -> BasicBoard:
     _insert_keepouts(dsn, board, transform)
     _insert_image_keepouts(dsn, board, transform)
     _insert_zones(dsn, board, transform, nets)
+    _insert_wiring(dsn, board, transform, nets)
     return board
 
 
@@ -333,10 +334,20 @@ def _insert_keepouts(dsn: DsnBoard, board: BasicBoard, transform: CoordinateTran
                     tiles=tiles,
                     blocks_wires=keepout.kind != "via_keepout",
                     blocks_vias=keepout.kind != "wire_keepout",
+                    clearance=not is_rule_area(keepout.area.name),
                 )
             )
 
 
+#: a structure keepout named with this prefix is a KiCad rule area (mckicad
+#: names them on export); it is checked for overlap only
+RULE_AREA_PREFIX = "rule_area"
+
+
+def is_rule_area(name: str | None) -> bool:
+    return bool(name) and name.startswith(RULE_AREA_PREFIX)
+
+
 def _area_border_tiles(shape: Shape, transform: CoordinateTransform) -> list:
     """Convex board tiles covering a keepout border shape.
 
@@ -461,6 +472,47 @@ def _placed_area_tiles(shape: Shape, place, transform: CoordinateTransform) -> l
     return [tile for tile in PolygonShape(pts).split_to_convex() if not tile.is_empty()]
 
 
+def _insert_wiring(dsn: DsnBoard, board: BasicBoard, transform: CoordinateTransform, nets) -> None:
+    """Tracks and vias already on the board, as fixed copper of their nets."""
+    layer_no = {layer.name: i for i, layer in enumerate(dsn.layers)}
+    signal_layers = [i for i, layer in enumerate(dsn.layers) if layer.is_signal]
+    numbers = {net.name: net.net_number for net in nets}
+    for wire in dsn.wires:
+        if wire.net not in numbers or wire.layer not in layer_no:
+            continue
+        c = wire.coords
+        corners = [transform.dsn_to_board_point(c[i], c[i + 1]) for i in range(0, len(c) - 1, 2)]
+        if len(corners) < 2:
+            continue
+        board.insert(
+            Trace(
+                net_nos=[numbers[wire.net]], fixed=True, layer=layer_no[wire.layer],
+                half_width=max(round(transform.dsn_to_board(wire.width / 2)), 1), corners=corners,
+            )
+        )
+    for via in dsn.vias:
+        padstack = dsn.padstack(via.padstack)
+        if via.net not in numbers or padstack is None or not padstack.shapes:
+            continue
+        layers: set[int] = set()
+        for shape in padstack.shapes:
+            if shape.layer in ("signal", "pcb"):
+                layers.update(signal_layers)
+            elif shape.layer in layer_no:
+                layers.add(layer_no[shape.layer])
+        location = transform.dsn_to_board_point(via.x, via.y)
+        pad = _pad_tile(max(padstack.shapes, key=_shape_extent), transform)
+        box = pad.bounding_box()
+        board.insert(
+            Via(
+                net_nos=[numbers[via.net]], fixed=True, padstack_name=via.padstack,
+                location=location, layers=sorted(layers or signal_layers),
+                shape=IntBox(box.ll.x + location.x, box.ll.y + location.y,
+                             box.ur.x + location.x, box.ur.y + location.y),
+            )
+        )
+
+
 def _insert_zones(dsn: DsnBoard, board: BasicBoard, transform: CoordinateTransform, nets) -> None:
     """Each DSN plane as a ConductionArea of its net on its layer."""
     layer_no = {layer.name: i for i, layer in enumerate(dsn.layers)}

src/freeroute/board/items.py

@@ -76,6 +76,11 @@ class ObstacleArea(Item):
     #: tracks" rule area, where vias are allowed), via_keepout only vias
     blocks_wires: bool = True
     blocks_vias: bool = True
+    #: False for a KiCad rule area: copper may not overlap it but may touch
+    #: it, since KiCad's DRC applies no clearance to a rule area. Every other
+    #: keepout may stand for copper (a net tie, a track kept as it is), so it
+    #: keeps the clearance unless named as a rule area.
+    clearance: bool = True
 
     def is_obstacle(self) -> bool:
         return True
@@ -109,6 +114,9 @@ class Via(Item):
 
     padstack_name: str = ""
     location: IntPoint = field(default_factory=lambda: IntPoint(0, 0))
+    #: layer indices the via's pads occupy, and the largest pad as a box
+    layers: list[int] = field(default_factory=list)
+    shape: object = None
 
 
 @dataclass

src/freeroute/board/search_tree.py

@@ -50,6 +50,8 @@ class TreeShape:
     #: which copper a keepout tile stops: "all", "wires" (a wire_keepout,
     #: vias allowed) or "vias" (a via_keepout)
     blocks: str = "all"
+    #: False for a rule area: copper may touch it, only overlap counts
+    clearance: bool = True
 
     def on_layer(self, layer: int) -> bool:
         return layer in self.layers
@@ -129,6 +131,8 @@ class ShapeSearchTree:
 
         Uses a strict 2-D overlap of the ``clearance``-expanded box, so tiles
         exactly ``clearance`` apart (touching after expansion) are allowed.
+        A rule area (``clearance=False``) only has to be clear of the copper
+        itself.
         """
         expanded = box.offset(clearance)
         for shape in self.overlapping(expanded):
@@ -136,6 +140,10 @@ class ShapeSearchTree:
                 continue
             if shape.blocks != "all" and shape.blocks != kind + "s":
                 continue  # a wire-only keepout does not stop a via, and so on
+            if not shape.clearance:
+                if shape.tile.overlaps(box):
+                    return True
+                continue
             if shape.exact is not None:
                 if overlaps_2d(shape.exact, expanded):
                     return True
@@ -143,6 +151,17 @@ class ShapeSearchTree:
                 return True
         return False
 
+    def rule_area_overlap(self, box: IntBox, layer: int, kind: str = "wire") -> bool:
+        """True if ``box`` overlaps a rule area on ``layer`` that stops ``kind``."""
+        for shape in self.overlapping(box):
+            if shape.clearance or not shape.on_layer(layer):
+                continue
+            if shape.blocks != "all" and shape.blocks != kind + "s":
+                continue
+            if shape.tile.overlaps(box):
+                return True
+        return False
+
     def clearance_conflict_shape(
         self, region, net_no: int, layer: int
     ) -> bool:
@@ -178,6 +197,13 @@ class ShapeSearchTree:
                     continue  # static input pair (e.g. pad vs pad) — not a routing DRC
                 if not (shape.layers & other.layers):
                     continue
+                if not (shape.clearance and other.clearance):
+                    # a rule area: only an overlap is a violation
+                    mine = shape.exact if shape.exact is not None else shape.tile
+                    theirs = other.exact if other.exact is not None else other.tile
+                    if overlaps_2d(mine, theirs):
+                        return shape
+                    continue
                 if shape.exact is None and other.exact is None:
                     if other.tile.overlaps(expanded):  # byte-identical box path
                         return shape

src/freeroute/cli.py

@@ -19,7 +19,7 @@ import argparse
 import sys
 
 from freeroute.dsn.reader import parse_dsn
-from freeroute.route.orders import best_of_orders
+from freeroute.route.orders import best_of_orders, promote_failures
 from freeroute.route.pipeline import (
     build_exact_routing_result,
     build_rooms_routing_result,
@@ -30,8 +30,8 @@ from freeroute.ses import write_ses
 #: which optional flags each engine actually implements. Anything not listed for
 #: an engine is rejected by :func:`_validate` rather than quietly ignored.
 ENGINE_OPTIONS: dict[str, frozenset[str]] = {
-    "grid": frozenset({"rip_up", "max_passes", "seed", "orders"}),
-    "exact": frozenset({"shove", "diagonal", "rip_up", "max_passes", "seed", "orders"}),
+    "grid": frozenset({"rip_up", "max_passes", "seed", "orders", "promote", "access", "rollback"}),
+    "exact": frozenset({"shove", "diagonal", "rip_up", "max_passes", "seed", "orders", "promote", "access", "rollback"}),
     "room": frozenset({"shove", "pack"}),
 }
 
@@ -44,6 +44,9 @@ _FLAG_NAMES = {
     "max_passes": "-mp/--max-passes",
     "seed": "--seed",
     "orders": "--orders",
+    "promote": "--promote-failures",
+    "access": "--access-cost",
+    "rollback": "--no-rollback",
 }
 
 
@@ -150,6 +153,36 @@ def build_parser() -> argparse.ArgumentParser:
         help="grid and exact engines: route N connection orders in parallel and keep the "
         "one leaving the fewest connections unrouted (the default order is one of them)",
     )
+    parser.add_argument(
+        "--promote-failures",
+        type=int,
+        metavar="R",
+        help="grid and exact engines: up to R rounds, each routing the connections that "
+        "failed so far first; keeps the best round",
+    )
+    parser.add_argument(
+        "--access-cost",
+        type=float,
+        metavar="C",
+        help="grid and exact engines: extra cost for a route to pass where it would close "
+        "another pin's way out while that pin still has connections to route (default 0: off)",
+    )
+    parser.add_argument(
+        "--no-rollback",
+        dest="rollback",
+        action="store_false",
+        help="grid and exact engines: keep every rip-up, as before. By default the "
+        "connections a rip-up displaces are rerouted at once and the rip-up is undone "
+        "if fewer connections end up routed",
+    )
+    parser.add_argument(
+        "--hole-to-hole",
+        type=float,
+        default=0.25,
+        metavar="MM",
+        help="grid and exact engines: least distance between the edges of any two via "
+        "holes, of one net or two (KiCad's min_hole_to_hole; default 0.25)",
+    )
     parser.add_argument(
         "--jobs",
         type=int,
@@ -177,6 +210,9 @@ def main(argv: list[str] | None = None) -> int:
             ("max_passes", args.max_passes is not None),
             ("seed", args.seed is not None),
             ("orders", args.orders is not None),
+            ("promote", args.promote_failures is not None),
+            ("access", args.access_cost is not None),
+            ("rollback", not args.rollback),
         )
         if asked
     ]
@@ -210,6 +246,9 @@ def main(argv: list[str] | None = None) -> int:
             "edge_clearance_mm": args.edge_clearance,
             "resolution": 2 if args.grid_resolution is None else args.grid_resolution,
             "heuristic_weight": args.heuristic_weight,
+            "access_cost": args.access_cost or 0.0,
+            "hole_to_hole_mm": args.hole_to_hole,
+            "rollback": args.rollback,
         }
     elif args.engine == "grid":
         options = {
@@ -218,12 +257,23 @@ def main(argv: list[str] | None = None) -> int:
             "max_passes": max_passes,
             "edge_clearance_mm": args.edge_clearance,
             "resolution": 1 if args.grid_resolution is None else args.grid_resolution,
+            "access_cost": args.access_cost or 0.0,
+            "hole_to_hole_mm": args.hole_to_hole,
+            "rollback": args.rollback,
         }
     if args.engine == "room":
         result = build_rooms_routing_result(
             dsn, layers=layers, shove=args.shove, pack=args.pack,
             edge_clearance_mm=args.edge_clearance,
         )
+    elif args.promote_failures and args.promote_failures > 1:
+        if args.orders:
+            parser.error("--orders and --promote-failures cannot be combined")
+        result, rounds = promote_failures(
+            dsn_text, args.engine, options, rounds=args.promote_failures, seed=args.seed
+        )
+        counts = ", ".join(str(m) for m, _z in rounds)
+        print(f"freeroute: {len(rounds)} rounds, unrouted {counts}; kept the best", file=sys.stderr)
     elif args.orders and args.orders > 1:
         result, kept, tried = best_of_orders(
             dsn_text, args.engine, options, orders=args.orders, seed=args.seed, jobs=args.jobs
@@ -247,6 +297,14 @@ def main(argv: list[str] | None = None) -> int:
         print(f"freeroute: {len(missing)} connection(s) not routed:", file=sys.stderr)
         for net, a, b, _zone in missing:
             print(f"  {net}: {a} to {b}", file=sys.stderr)
+    if result.narrowed:
+        print(
+            f"freeroute: {len(result.narrowed)} connection(s) of a wider net class only fitted "
+            "at the default width; their nets are written at the default width:",
+            file=sys.stderr,
+        )
+        for net, a, b in result.narrowed:
+            print(f"  {net}: {a} to {b}", file=sys.stderr)
     if in_zone:
         print(
             f"freeroute: {len(in_zone)} more connection(s) left to a zone fill that may join them:",

src/freeroute/dsn/model.py

@@ -27,6 +27,8 @@ __all__ = [
     "NetPin",
     "Net",
     "NetClass",
+    "WiringVia",
+    "WiringWire",
     "Keepout",
     "DsnBoard",
 ]
@@ -186,6 +188,26 @@ class Keepout:
     kind: str = "keepout"  # keepout | via_keepout | wire_keepout | place_keepout
 
 
+@dataclass
+class WiringWire:
+    """A track already on the board: ``(wire (path LAYER WIDTH x y ...) (net N))``."""
+
+    net: str
+    layer: str
+    width: float
+    coords: list[float] = field(default_factory=list)
+
+
+@dataclass
+class WiringVia:
+    """A via already on the board: ``(via PADSTACK x y (net N))``."""
+
+    net: str
+    padstack: str
+    x: float
+    y: float
+
+
 @dataclass
 class DsnBoard:
     """The fully parsed DSN file."""
@@ -197,6 +219,9 @@ class DsnBoard:
     layers: list[Layer] = field(default_factory=list)
     #: copper zones, as planes of a net
     planes: list[Plane] = field(default_factory=list)
+    #: copper already routed (the ``wiring`` scope), kept fixed
+    wires: list[WiringWire] = field(default_factory=list)
+    vias: list[WiringVia] = field(default_factory=list)
     #: bounding-box boundary shape (layer ``pcb``), if present
     boundary: Shape | None = None
     #: outline shapes (layer ``signal``)

src/freeroute/dsn/reader.py

@@ -9,6 +9,8 @@ tolerant ``skip_scope`` behaviour.
 
 from __future__ import annotations
 
+import re
+
 from .model import (
     ClearanceRule,
     ComponentPlace,
@@ -25,6 +27,8 @@ from .model import (
     Pin,
     Resolution,
     WidthRule,
+    WiringVia,
+    WiringWire,
 )
 from .sexp import SExp, parse
 from .shapes import Shape, read_area, read_shape
@@ -481,12 +485,26 @@ def _read_network(node: SExp, board: DsnBoard) -> None:
 # --- top level ---------------------------------------------------------------
 
 
+_STRING_QUOTE = re.compile(r"\(\s*string_quote\s+(\S)\s*\)")
+
+
+def _declared_quote(text: str) -> str:
+    """The quote character the file declares in ``(string_quote X)``.
+
+    Only that character opens a string. Without a declaration both kinds are
+    accepted, as before: KiCad declares ``"`` and then writes a bare ``'``
+    where a value is a single quote mark, e.g. a keycap part number.
+    """
+    found = _STRING_QUOTE.search(text[:4096])
+    return found.group(1) if found else "\"'"
+
+
 def parse_dsn(text: str) -> DsnBoard:
     """Parse DSN ``text`` into a :class:`DsnBoard`.
 
     Raises :class:`DsnParseError` if the top-level scope is not ``(pcb ...)``.
     """
-    top = parse(text)
+    top = parse(text, _declared_quote(text))
     if top.head != "pcb":
         raise DsnParseError(
             f"not a Specctra DSN file: expected top-level '(pcb ...)', got '({top.head} ...)'"
@@ -515,11 +533,45 @@ def parse_dsn(text: str) -> DsnBoard:
             _read_placement(it, board)
         elif head == "network":
             _read_network(it, board)
-        # `wiring` and unknown scopes are intentionally ignored for now.
+        elif head == "wiring":
+            _read_wiring(it, board)
+        # unknown scopes are ignored
 
     return board
 
 
+def _read_wiring(node: SExp, board: DsnBoard) -> None:
+    """Tracks and vias already on the board. They stay where they are: the
+    router treats them as copper of their net that other nets keep clear of."""
+    for it in node.items:
+        if not isinstance(it, SExp):
+            continue
+        net_scope = it.child("net")
+        net = _first_value(net_scope) if net_scope is not None else None
+        if not net:
+            continue  # netless copper would need a keepout, not a wire
+        if it.head == "wire":
+            path = it.child("path") or it.child("polyline_path")
+            vals = [v.text for v in path.values()] if path is not None else []
+            if len(vals) < 6:
+                continue
+            try:
+                width = float(vals[1])
+                coords = [float(v) for v in vals[2:]]
+            except ValueError:
+                continue
+            board.wires.append(WiringWire(net=net, layer=vals[0], width=width, coords=coords))
+        elif it.head == "via":
+            vals = [v.text for v in it.values()]
+            if len(vals) < 3:
+                continue
+            try:
+                x, y = float(vals[1]), float(vals[2])
+            except ValueError:
+                continue
+            board.vias.append(WiringVia(net=net, padstack=vals[0], x=x, y=y))
+
+
 def _read_plane(node: SExp):
     """``(plane <net> (polygon <layer> <width> x y ...))`` -> :class:`Plane`."""
     from .model import Plane

src/freeroute/route/exact_router.py

@@ -31,7 +31,7 @@ from dataclasses import dataclass, field
 import math
 
 from freeroute.board.board import BasicBoard
-from freeroute.board.items import Pin
+from freeroute.board.items import Pin, Via
 from freeroute.board.search_tree import ShapeSearchTree, TreeShape
 from freeroute.geometry import (
     IntBox,
@@ -42,6 +42,7 @@ from freeroute.geometry import (
     segment_octagon,
     shove_segment,
 )
+from freeroute.geometry.polyline import corner_box
 
 from .grid_router import RouteResult, route_board
 
@@ -95,6 +96,12 @@ def route_board_exact(
     resolution: int = 1,
     heuristic_weight: float = 1.0,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    rollback: bool = True,
+    net_widths: dict[int, int] | None = None,
+    via_drill: int | None = None,
+    hole_to_hole: int = 0,
 ) -> ExactRouteResult:
     """Route ``board`` orthogonally and verify the result with exact geometry.
 
@@ -124,6 +131,12 @@ def route_board_exact(
         resolution=resolution,
         heuristic_weight=heuristic_weight,
         seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        rollback=rollback,
+        net_widths=net_widths,
+        via_drill=via_drill,
+        hole_to_hole=hole_to_hole,
     )
     edge = 0 if edge_clearance is None else edge_clearance
     outline = board.outline
@@ -142,6 +155,10 @@ def route_board_exact(
         pin_layers = frozenset(layer for layer in pin.layers if layer in signal_layers)
         if pin_layers:
             tree.insert(TreeShape(next(owner), net, pin_layers, box))
+    for net, copper_layers, box in board.get_fixed_copper():
+        on = frozenset(layer for layer in copper_layers if layer in signal_layers)
+        if on and not box.is_empty():
+            tree.insert(TreeShape(next(owner), net, on, box))
     for obstacle in board.get_obstacle_areas():
         if obstacle.layer not in signal_layers:
             continue
@@ -153,35 +170,53 @@ def route_board_exact(
             box = tile.bounding_box()
             if not box.is_empty():
                 tree.insert(
-                    TreeShape(next(owner), -1, frozenset({obstacle.layer}), box, blocks=blocks)
+                    TreeShape(
+                        next(owner), -1, frozenset({obstacle.layer}), box,
+                        blocks=blocks, clearance=obstacle.clearance,
+                    )
                 )
 
     via_layers = frozenset(signal_layers)
     accepted: dict[int, _Accepted] = {}
+    fixed_vias = {
+        (item.net_nos[0], item.location)
+        for item in board.get_items()
+        if isinstance(item, Via) and item.fixed and item.net_nos
+    }
 
     # Verify connection by connection, so one conflicting segment of a
     # 25-pin supply net costs that one connection, not the whole net.
     rejected: list[tuple[int, str, str]] = []
     ends_list = result.connection_ends or [("?", "?", "")] * len(result.connections)
+    # each net is checked at the width it will be written at: its class's
+    # when all of its connections went in at that, else the default
+    net_half = dict(result.net_half)
     for (net_no, wires, vias), ends in sorted(
         zip(result.connections, ends_list, strict=False), key=lambda c: c[0][0]
     ):
-        boxes = _copper_boxes(wires, vias, half_width, via_layers, via_half)
-        wire_count = len(_copper_boxes(wires, [], half_width, via_layers, via_half))
+        wire_half = net_half.get(net_no, half_width)
+        boxes = _copper_boxes(wires, vias, wire_half, via_layers, via_half)
+        wire_count = len(_copper_boxes(wires, [], wire_half, via_layers, via_half))
         if any(
             tree.clearance_conflict(
                 box, net_no, layer, clearance, "wire" if i < wire_count else "via"
             )
             for i, (box, box_layers) in enumerate(boxes)
             for layer in box_layers
-        ) or (outline is not None and not all(outline.box_clear(b, edge) for b, _ in boxes)):
+        ) or _end_in_rule_area(tree, wires, wire_half) or (
+            outline is not None and not all(outline.box_clear(b, edge) for b, _ in boxes)
+        ):
             rejected.append((net_no, *ends))
             continue  # exact-clearance conflict -> drop (may be recovered by shove)
         acc = accepted.get(net_no)
         if acc is None:
             acc = accepted[net_no] = _Accepted(wires=[], vias=[])
         acc.wires.extend(wires)
-        acc.vias.extend(vias)
+        # connections of one net that end on the same plane cell share its
+        # via: write it once, and never on top of a via already on the board
+        acc.vias.extend(
+            v for v in dict.fromkeys(vias) if v not in acc.vias and (net_no, v) not in fixed_vias
+        )
         for box, box_layers in boxes:
             oid = next(owner)
             tree.insert(TreeShape(oid, net_no, box_layers, box, routed=True))
@@ -231,6 +266,17 @@ def route_board_exact(
     for net_no, acc in accepted.items():
         clean.wires[net_no] = acc.wires
         clean.vias[net_no] = acc.vias
+    # shove and the diagonal pass lay copper at the default width: nets they
+    # recovered, and nets whose traces shove pushed aside
+    reshaped = (set(accepted) - accepted_before_recovery) | {
+        net for net, acc in accepted.items() if acc.shove_count
+    }
+    if diagonal:
+        reshaped = set(accepted)
+    clean.net_half = {
+        net: half for net, half in net_half.items() if net in accepted and net not in reshaped
+    }
+    clean.narrowed = list(result.narrowed)
 
     drc_clean = tree.has_violation(clearance) is None
     return ExactRouteResult(result=clean, tree=tree, drc_clean=drc_clean, shoves=shoves)
@@ -588,6 +634,17 @@ def _net_boxes(result, net_no, half_width, via_layers, via_half=None):
     )
 
 
+def _end_in_rule_area(tree, wires, half_width) -> bool:
+    """A wire's tiles stop at its end points, but a track ends in a round cap
+    half its width beyond them. Against other copper the pad or via there
+    covers it; a rule area has no clearance to absorb it, so check it."""
+    for layer, points in wires:
+        for end in (points[0], points[-1]):
+            if tree.rule_area_overlap(corner_box(end, half_width), layer):
+                return True
+    return False
+
+
 def _copper_boxes(wires, vias, half_width, via_layers, via_half=None):
     via_half = via_half or half_width
     boxes: list[tuple[IntBox, frozenset[int]]] = []

src/freeroute/route/grid_router.py

@@ -31,8 +31,9 @@ import math
 import random
 
 from freeroute.board.board import BasicBoard
-from freeroute.board.items import ConductionArea, ObstacleArea, Pin
+from freeroute.board.items import ConductionArea, ObstacleArea, Pin, Via
 from freeroute.geometry import IntBox, IntPoint
+from freeroute.geometry.polyline import corner_box
 
 __all__ = ["GridRouter", "RouteResult", "route_board"]
 
@@ -60,7 +61,10 @@ class RouteResult:
     ``routed_net_numbers`` are the nets that got any wire or via.
     """
 
-    __slots__ = ("wires", "vias", "half_width", "unrouted", "connections", "connection_ends", "failed")
+    __slots__ = (
+        "wires", "vias", "half_width", "unrouted", "connections", "connection_ends", "failed",
+        "net_half", "narrowed",
+    )
 
     def __init__(self, half_width: int) -> None:
         self.wires: dict[int, list[tuple[int, list[IntPoint]]]] = {}
@@ -75,6 +79,10 @@ class RouteResult:
         self.connection_ends: list[tuple[str, str, str]] = []
         #: connections left unrouted: (net_no, one end, the other end)
         self.failed: list[tuple[int, str, str]] = []
+        #: half width of each net routed wider than the default (its class)
+        self.net_half: dict[int, int] = {}
+        #: connections of a wider class that only fitted at the default width
+        self.narrowed: list[tuple[int, str, str]] = []
 
     def add_wire(self, net_no: int, layer: int, path: list[IntPoint]) -> None:
         self.wires.setdefault(net_no, []).append((layer, path))
@@ -112,6 +120,9 @@ class _Connection:
         "b_group",
         "a_end",
         "b_end",
+        "path",
+        "narrow",
+        "half",
     )
 
     def __init__(self, index: int, net_no: int, a: Pin, b: Pin) -> None:
@@ -133,6 +144,12 @@ class _Connection:
         self.b_group: tuple[list[Pin], list] = ([b], [])
         self.a_end: Pin | None = a
         self.b_end: Pin | None = b
+        # the node path last committed, so a rip-up can be undone
+        self.path: list[Node] | None = None
+        # a connection of a wider class that did not fit at that width is
+        # routed at the default width instead; the half width it went in at
+        self.narrow = False
+        self.half = 0
 
 
 class GridRouter:
@@ -156,11 +173,32 @@ class GridRouter:
         resolution: int = 1,
         heuristic_weight: float = 1.0,
         seed: int | None = None,
+        route_first: frozenset | None = None,
+        access_cost: float = 0.0,
+        rollback: bool = True,
+        net_widths: dict[int, int] | None = None,
+        via_drill: int | None = None,
+        hole_to_hole: int = 0,
     ) -> None:
         self.board = board
+        # Pin access: while a pin still has connections to route, the cells
+        # its route would leave by (its end cells, the via it may need there,
+        # and the clearance around both) cost other nets this much extra, so
+        # they route round a fine-pitch pin's way out instead of sealing it.
+        self.access_cost = max(float(access_cost), 0.0)
+        self._doorways: dict[Node, list[tuple[int, int]]] = {}
+        self._pending: dict[int, int] = {}
+        # Rip-up as a transaction: the connections a rip-up route crosses are
+        # rerouted at once, and if fewer connections are routed afterwards
+        # than before, everything goes back as it was. On by default: over
+        # 8 net orders it left 25 to 30 fewer connections unrouted on dense
+        # boards and was never clearly worse.
+        self.rollback = bool(rollback)
         # None keeps the deterministic order; a seed shuffles which connection
         # routes first, to measure how much a result owes to the order
         self.seed = seed
+        # connections, as (net_no, one end, other end), to route before the rest
+        self.route_first = frozenset(route_first or ())
         # how far (in cells) an escape stub may run to leave a walled-in pin
         self._escape_cells = 12
         self._crowded_cache: dict = {}
@@ -201,6 +239,34 @@ class GridRouter:
         self.edge_clearance = 0 if edge_clearance is None else edge_clearance
         need = self.via_half + self.clearance + self.half_width
         self.via_reach = max(0, math.ceil(need / self.step) - 1)
+        # Net classes wider than the default: the grid is laid out for the
+        # default width, so a wider trace must also find the cells around its
+        # own free, out to its extra half width, and claims a wider halo.
+        self._net_half = {
+            net: max(width // 2, 1)
+            for net, width in (net_widths or {}).items()
+            if width // 2 > self.half_width
+        }
+        self._spread: list[tuple[int, int]] = []  # the current search's
+        self._cur_half = self.half_width
+        self._halo_by_half: dict[int, list[tuple[int, int]]] = {self.half_width: self._halo_offsets}
+        # Hole-to-hole spacing holds between any two vias, of one net or two.
+        # Other nets' vias are kept further apart already; a net's own vias
+        # (every pin of a supply dropping to its plane) are not, so a via
+        # must keep its drill plus the spacing from every via centre, except
+        # an own-net via at the very same cell, which it simply reuses.
+        drill = via_drill if via_drill else 2 * self.via_half
+        need = drill + max(hole_to_hole, 0)
+        reach = math.ceil(need / self.step)
+        self._hole_offsets = [
+            (dx, dy)
+            for dx in range(-reach, reach + 1)
+            for dy in range(-reach, reach + 1)
+            if (dx or dy) and math.hypot(dx, dy) * self.step < need
+        ]
+        self._via_nets: dict[Cell, dict[int, int]] = {}  # routed via centres
+        self._fixed_vias: dict[Cell, int] = {}
+        self._fixed_via_points: set[tuple[int, IntPoint]] = set()
 
         if layers is None:
             layers = [i for i, layer in enumerate(board.layer_structure.arr) if layer.is_signal]
@@ -228,6 +294,11 @@ class GridRouter:
         # trace halos: node -> indices of the connections claiming it
         self._halo: dict[Node, list[int]] = {}
         self._rasterize_obstacles()
+        self._rasterize_fixed_copper()
+        for item in board.get_items():
+            if isinstance(item, Via) and item.fixed and item.net_nos:
+                self._fixed_vias[self._cell_of(item.location)] = item.net_nos[0]
+                self._fixed_via_points.add((item.net_nos[0], item.location))
 
     # --- grid helpers -------------------------------------------------------
 
@@ -286,6 +357,13 @@ class GridRouter:
         margin = self.clearance + self.half_width
         outline = self.board.outline
         self._via_edge_block: set[Cell] = set()
+        # wire keepouts as boxes, to check a pin stub the way the exact engine will
+        self._keepout_boxes: dict[int, list[tuple[IntBox, bool]]] = {}
+        # via keepouts as boxes, and other copper a via in a pad must clear
+        self._via_keepout_boxes: list[tuple[IntBox, bool]] = []
+        self._static_copper: list[tuple[IntBox, int]] | None = None
+        # pin end nodes no wire can reach without entering a keepout
+        self._via_only: set[Node] = set()
         if outline is not None:
             # cells too close to the real outline (rounded corners included):
             # for a trace on every layer, and separately for a via's wider copper
@@ -322,11 +400,29 @@ class GridRouter:
                     if box.is_empty():
                         continue
                     # the same distance the exact engine verifies against
-                    for cell in self._cells_in_box(box, margin):
+                    if item.blocks_wires:
+                        self._keepout_boxes.setdefault(item.layer, []).append(
+                            (box, item.clearance)
+                        )
+                    # a rule area takes no clearance: a trace may touch it
+                    reach = margin if item.clearance else self.half_width
+                    for cell in self._cells_in_box(box, reach):
                         if item.blocks_wires:
                             self._keepout.add((*cell, item.layer))
                         if item.blocks_vias:
                             self._via_keepout.add((*cell, item.layer))
+                    if item.blocks_vias:
+                        self._via_keepout_boxes.append((box, item.clearance))
+
+    def _rasterize_fixed_copper(self) -> None:
+        """Tracks and vias already on the board: copper of their net, which
+        other nets keep the same distance from as from a pad."""
+        margin = self.clearance + self.half_width
+        for net, layers, box in self.board.get_fixed_copper():
+            on = [layer for layer in layers if layer in self.layers]
+            for cell in self._cells_in_box(box, margin):
+                for layer in on:
+                    self._pad_block.setdefault((*cell, layer), set()).add(net)
 
     # --- occupancy cost -----------------------------------------------------
 
@@ -338,6 +434,30 @@ class GridRouter:
         allow_ripup: bool,
         conns: list[_Connection],
         wire_keepout: bool = True,
+    ) -> float | None:
+        """:meth:`_enter_cost_base`, and for a trace wider than the default
+        the same for every cell its extra width reaches (the worst of them)."""
+        cost = self._enter_cost_base(cell, layer, net_no, allow_ripup, conns, wire_keepout)
+        if cost is None or not self._spread:
+            return cost
+        for dx, dy in self._spread:
+            c = (cell[0] + dx, cell[1] + dy)
+            if not (0 <= c[0] < self.cols and 0 <= c[1] < self.rows):
+                return None
+            more = self._enter_cost_base(c, layer, net_no, allow_ripup, conns, wire_keepout)
+            if more is None:
+                return None
+            cost = max(cost, more)
+        return cost
+
+    def _enter_cost_base(
+        self,
+        cell: Cell,
+        layer: int,
+        net_no: int,
+        allow_ripup: bool,
+        conns: list[_Connection],
+        wire_keepout: bool = True,
     ) -> float | None:
         """Cost to enter ``(cell, layer)`` for ``net_no``; ``None`` if blocked.
 
@@ -392,14 +512,72 @@ class GridRouter:
             for layer in self.layers:
                 if (*c, layer) in self._via_keepout:
                     return False
-                if self._enter_cost(c, layer, net_no, False, conns, wire_keepout=False) != 0.0:
+                if self._enter_cost_base(c, layer, net_no, False, conns, wire_keepout=False) != 0.0:
                     return False
-        return True
+        return self._holes_clear(cell, net_no)
+
+    def _via_nets_at(self, cell: Cell) -> set[int]:
+        nets = {net for net, n in self._via_nets.get(cell, {}).items() if n > 0}
+        fixed = self._fixed_vias.get(cell)
+        if fixed is not None:
+            nets.add(fixed)
+        return nets
+
+    def _holes_clear(self, cell: Cell, net_no: int) -> bool:
+        """No via centre within hole-to-hole reach, but an own-net one here."""
+        if self._via_nets_at(cell) - {net_no}:
+            return False
+        cx, cy = cell
+        return not any(self._via_nets_at((cx + dx, cy + dy)) for dx, dy in self._hole_offsets)
 
     # --- A* search ----------------------------------------------------------
 
+    def _conn_half(self, conn: _Connection) -> int:
+        """The half width a connection is routed at: its class's, unless it
+        has fallen back to the default."""
+        return self.half_width if conn.narrow else self._net_half.get(conn.net_no, self.half_width)
+
+    def _spread_for(self, half: int) -> list[tuple[int, int]]:
+        """Cells a trace of ``half`` also needs free: those whose centre is
+        within its extra half width (plus half a cell, for the grid)."""
+        extra = half - self.half_width
+        if extra <= 0:
+            return []
+        reach = math.ceil(extra / self.step) + 1
+        limit = extra + self.step / 2
+        return [
+            (dx, dy)
+            for dx in range(-reach, reach + 1)
+            for dy in range(-reach, reach + 1)
+            if (dx or dy) and math.hypot(dx, dy) * self.step <= limit
+        ]
+
+    def _halo_for(self, half: int) -> list[tuple[int, int]]:
+        """Cells a committed trace of ``half`` claims from default-width traces."""
+        offsets = self._halo_by_half.get(half)
+        if offsets is None:
+            need = half + self.clearance + self.half_width
+            reach = math.ceil(need / self.step)
+            offsets = self._halo_by_half[half] = [
+                (dx, dy)
+                for dx in range(-reach, reach + 1)
+                for dy in range(-reach, reach + 1)
+                if (dx or dy) and math.hypot(dx, dy) * self.step < need
+            ]
+        return offsets
+
     def _search(
         self, conn: _Connection, allow_ripup: bool, conns: list[_Connection]
+    ) -> list[Node] | None:
+        half = self._conn_half(conn)
+        self._cur_half, self._spread = half, self._spread_for(half)
+        try:
+            return self._search_at_width(conn, allow_ripup, conns)
+        finally:
+            self._cur_half, self._spread = self.half_width, []
+
+    def _search_at_width(
+        self, conn: _Connection, allow_ripup: bool, conns: list[_Connection]
     ) -> list[Node] | None:
         goal_cell = self._group_target(conn.b_group)
         if not conn.b_group[0] and any(z.layer in self._power_layers for z in conn.b_group[1]):
@@ -409,7 +587,14 @@ class GridRouter:
         goals = self._group_ends(conn.b_group, conn.net_no, conns)
         if not starts or not goals:
             return None
-        common = sorted(set(starts) & set(goals))
+        # A start that is already an end joins at once, except that ending on
+        # a plane there needs a via: one that cannot be placed (a via keepout,
+        # another net's pad) is no end, and the search goes on from there.
+        common = [
+            n for n in sorted(set(starts) & set(goals))
+            if not isinstance(goals[n], ConductionArea)
+            or self._via_placeable((n[0], n[1]), conn.net_no, conns)
+        ]
         if common:
             conn.a_end, conn.b_end = starts[common[0]], goals[common[0]]
             return [common[0]]
@@ -419,10 +604,11 @@ class GridRouter:
         g_score: dict[Node, float] = {}
         came_from: dict[Node, Node] = {}
         # a stub costs its length, so the nearest cell wins unless it is blocked
-        goal_stub = {n: self._stub_cost(p, n) for n, p in goals.items() if p is not None}
+        # a pin end costs its stub; a zone or plane end is entered normally
+        goal_stub = {n: self._stub_cost(p, n) for n, p in goals.items() if isinstance(p, Pin)}
         for s in sorted(starts):
             pin = starts[s]
-            g_score[s] = self._stub_cost(pin, s) if pin is not None else 0.0
+            g_score[s] = self._stub_cost(pin, s) if isinstance(pin, Pin) else 0.0
             heapq.heappush(open_heap, (g_score[s] + self._h(s, goal_cell), s))
 
         # Via footprints are checked lazily: a layer change goes on the heap as
@@ -441,6 +627,12 @@ class GridRouter:
                 ok = via_ok.get(cell)
                 if ok is None:
                     ok = via_ok[cell] = self._via_placeable(cell, net_no, conns)
+                # a via leaving or reaching a walled-in pin goes in its pad
+                # (see _commit), so it has to fit there exactly
+                for node, ends in ((source, starts), (target, goals)):
+                    pin = ends.get(node)
+                    if ok and isinstance(pin, Pin) and self._walled(node):
+                        ok = self._via_fits_at(pin.location, net_no)
                 if ok:
                     self._relax(source, target, g_via, goal_cell, g_score, came_from, open_heap)
                 continue
@@ -460,23 +652,34 @@ class GridRouter:
                     return path
             cx, cy, cl = current
             base = g_score[current]
-            for dx, dy in self._neighbours:
+            # A cell inside a wire keepout (a pin there, or where a via
+            # landed) may only be left by another via: a wire from it would
+            # start inside the keepout.
+            blocked = current in self._keepout or current in self._via_only
+            neighbours = () if blocked else self._neighbours
+            for dx, dy in neighbours:
                 cell = (cx + dx, cy + dy)
                 if not (0 <= cell[0] < self.cols and 0 <= cell[1] < self.rows):
                     continue
                 nxt = (*cell, cl)
                 if nxt in goal_stub:  # a pin end; a zone end is entered normally
+                    if nxt in self._keepout or nxt in self._via_only:
+                        continue  # a pin inside a keepout is reached by a via only
                     enter = goal_stub[nxt]
                 else:
                     enter = self._enter_cost(cell, cl, net_no, allow_ripup, conns)
                     if enter is None:
                         continue
+                    if self._doorways:
+                        enter += self._access(nxt, net_no)
                 step = 1.0 if dx == 0 or dy == 0 else math.sqrt(2)
                 self._relax(
                     current, nxt, base + step + enter, goal_cell, g_score, came_from, open_heap
                 )
             if len(self.layers) > 1:
                 g_via = base + self.via_cost
+                if self._doorways:
+                    g_via += self._access(current, net_no)
                 for layer in self.layers:
                     if layer == cl:
                         continue
@@ -493,12 +696,35 @@ class GridRouter:
     # copper too, or a stub ends up closer than clearance to a trace in the
     # cell beside it.
 
-    def _stub_cells(self, pin_location: IntPoint, cell: Cell) -> list[Cell]:
+    def _walled(self, node: Node) -> bool:
+        """A pin end no wire may leave or reach: only a via in its pad will do."""
+        return node in self._keepout or node in self._via_only
+
+    def _via_fits_at(self, point: IntPoint, net_no: int) -> bool:
+        """A via centred exactly on ``point`` clears every via keepout and all
+        other nets' pads and fixed copper (what a via in a pad must meet)."""
+        via = IntBox(point.x - self.via_half, point.y - self.via_half,
+                     point.x + self.via_half, point.y + self.via_half)
+        grown = via.offset(self.clearance)
+        for box, needs in self._via_keepout_boxes:
+            if box.overlaps(grown if needs else via):
+                return False
+        if self._static_copper is None:
+            copper = [
+                (p.shape.bounding_box(), p.net_nos[0] if p.net_nos else -1)
+                for p in self.board.get_pins()
+                if p.shape is not None and any(layer in self.layers for layer in p.layers)
+            ]
+            copper += [(box, net) for net, _, box in self.board.get_fixed_copper()]
+            self._static_copper = copper
+        return not any(net != net_no and box.overlaps(grown) for box, net in self._static_copper)
+
+    def _stub_cells(self, pin_location: IntPoint, cell: Cell, half: int | None = None) -> list[Cell]:
         """Cells where another net's trace would come too close to the stub."""
         from freeroute.board.outline import _point_segment
 
         end = self._cell_center(cell)
-        reach = 2 * self.half_width + self.clearance
+        reach = (half or self._cur_half) + self.half_width + self.clearance
         box = IntBox(
             min(pin_location.x, end.x), min(pin_location.y, end.y),
             max(pin_location.x, end.x), max(pin_location.y, end.y),
@@ -509,7 +735,27 @@ class GridRouter:
             if _point_segment(self._cell_center(c), pin_location, end) < reach
         ]
 
-    def _stub_clear(self, pin: Pin, cell: Cell, layer: int, net_no: int, conns) -> bool:
+    def _stub_clear(
+        self, pin: Pin, cell: Cell, layer: int, net_no: int, conns, keepouts_only: bool = False
+    ) -> bool:
+        keepouts = self._keepout_boxes.get(layer)
+        if keepouts:
+            # the stub is off the grid, so check it exactly, as the exact
+            # engine will: its copper grown by clearance must miss every keepout
+            from freeroute.geometry.polyline import Polyline, PolylineShape
+
+            end = self._cell_center(cell)
+            if end != pin.location:
+                for tile in PolylineShape(Polyline([pin.location, end]), self._cur_half).tiles():
+                    grown = tile.offset(self.clearance)
+                    if any(k.overlaps(grown if needs else tile) for k, needs in keepouts):
+                        return False
+                # the track's round end at the pin, for a rule area
+                cap = corner_box(pin.location, self._cur_half)
+                if any(not needs and k.overlaps(cap) for k, needs in keepouts):
+                    return False
+        if keepouts_only:
+            return True
         for c in self._stub_cells(pin.location, cell):
             owner = self._cell_owner.get((*c, layer))
             if owner is not None and conns[owner].net_no != net_no:
@@ -615,6 +861,13 @@ class GridRouter:
             nodes |= self._escape_nodes(pin, net_no, conns, layers, (cx, cy))
         if not nodes:  # nothing clear: fall back to the nearest cell, as before
             nodes = {(cx, cy, layer) for layer in layers}
+            if self._keepout_boxes and not any(
+                self._stub_clear(pin, (cx, cy), layer, net_no, conns, keepouts_only=True)
+                for layer in layers
+            ):
+                # no wire can reach the pin without entering a keepout: the
+                # route has to arrive by a via, which goes in the pad
+                self._via_only.update(nodes)
         return nodes
 
     def _crowded(self, pin: Pin, net_no: int) -> bool:
@@ -728,6 +981,7 @@ class GridRouter:
     # --- commit / rip -------------------------------------------------------
 
     def _commit(self, conn: _Connection, path: list[Node]) -> None:
+        conn.path = list(path)
         wire_segs, via_cells = _split_path(path)
         via_cells = list(via_cells)
         if isinstance(conn.a_end, ConductionArea):
@@ -736,11 +990,16 @@ class GridRouter:
             via_cells.append((path[-1][0], path[-1][1]))
         conn.trace_cells = [(cell, layer) for layer, cells in wire_segs for cell in cells]
         conn.via_cells = list(via_cells)
+        for cell in conn.via_cells:
+            count = self._via_nets.setdefault(cell, {})
+            count[conn.net_no] = count.get(conn.net_no, 0) + 1
         for cell, layer in conn.trace_cells:
             self._cell_owner[(*cell, layer)] = conn.index
+        conn.half = half = self._conn_half(conn)
+        halo = self._halo_for(half)
         conn.halo_nodes = []
         for (cx, cy), layer in conn.trace_cells:
-            for dx, dy in self._halo_offsets:
+            for dx, dy in halo:
                 x, y = cx + dx, cy + dy
                 if 0 <= x < self.cols and 0 <= y < self.rows:
                     node = (x, y, layer)
@@ -757,13 +1016,26 @@ class GridRouter:
             if not isinstance(pin, Pin):
                 continue  # ended on a zone or a plane: no stub
             cell = cells[at]
-            for c in self._stub_cells(pin.location, cell):
+            for c in self._stub_cells(pin.location, cell, half):
                 node = (*c, layer)
                 if node not in self._cell_owner:
                     self._cell_owner[node] = conn.index
                     conn.trace_cells.append((c, layer))
+        # A pin inside a wire keepout can only leave by a via. Its stub to the
+        # cell centre would be track inside the keepout, so the via goes on
+        # the pin itself (a via in its own pad) and the stub is left out.
+        in_pad: dict[int, IntPoint] = {}
+        if len(wire_segs) > 1:
+            for idx, pin in ((0, conn.a_end), (len(wire_segs) - 1, conn.b_end)):
+                layer, cells = wire_segs[idx]
+                node = (*cells[0], layer)
+                walled = node in self._keepout or node in self._via_only
+                if isinstance(pin, Pin) and len(cells) == 1 and walled:
+                    in_pad[idx] = pin.location
         conn.wires = []
         for idx, (layer, cells) in enumerate(wire_segs):
+            if idx in in_pad:
+                continue
             points = [self._cell_center(c) for c in cells]
             if idx == 0 and isinstance(conn.a_end, Pin):
                 points.insert(0, conn.a_end.location)
@@ -773,7 +1045,11 @@ class GridRouter:
             if len(points) >= 2:
                 conn.wires.append((layer, points))
         conn.vias = [self._cell_center(c) for c in conn.via_cells]
+        for idx, location in in_pad.items():
+            # via k joins wire segments k and k + 1
+            conn.vias[0 if idx == 0 else idx - 1] = location
         conn.routed = True
+        self._settle(conn, -1)
 
     def _rip(self, conn: _Connection) -> None:
         for cell, layer in conn.trace_cells:
@@ -791,11 +1067,16 @@ class GridRouter:
                     del self._halo[node]
         conn.halo_nodes = []
         conn.trace_cells = []
+        for cell in conn.via_cells:
+            count = self._via_nets.get(cell)
+            if count and count.get(conn.net_no):
+                count[conn.net_no] -= 1
         conn.via_cells = []
         conn.wires = []
         conn.vias = []
         conn.routed = False
         conn.rip_count += 1
+        self._settle(conn, +1)
 
     def _crossed_owners(self, path: list[Node], net_no: int, conns: list[_Connection]) -> set[int]:
         owners: set[int] = set()
@@ -811,6 +1092,50 @@ class GridRouter:
                     owners.add(i)
         return owners
 
+    # --- pin access ---------------------------------------------------------
+
+    @staticmethod
+    def _group_pins(conn: _Connection):
+        return [*conn.a_group[0], *conn.b_group[0]]
+
+    def _build_doorways(self, conns: list[_Connection]) -> None:
+        """Map every cell that would close a pin's way out to that pin."""
+        spread = [(0, 0), *self._halo_offsets]
+        done: set[int] = set()
+        for conn in conns:
+            for pin in self._group_pins(conn):
+                self._pending[id(pin)] = self._pending.get(id(pin), 0) + 1
+                if id(pin) in done:
+                    continue
+                done.add(id(pin))
+                claim = (id(pin), conn.net_no)
+                exits: set[Node] = set()
+                for x, y, layer in self._end_nodes(pin, conn.net_no, conns):
+                    exits.add((x, y, layer))
+                    for c in self._via_cells((x, y)):
+                        exits.update((*c, other) for other in self.layers)
+                cells: set[Node] = set()
+                for x, y, layer in exits:
+                    for dx, dy in spread:
+                        if 0 <= x + dx < self.cols and 0 <= y + dy < self.rows:
+                            cells.add((x + dx, y + dy, layer))
+                for node in cells:
+                    self._doorways.setdefault(node, []).append(claim)
+
+    def _settle(self, conn: _Connection, delta: int) -> None:
+        if not self._pending:
+            return
+        for pin in self._group_pins(conn):
+            if id(pin) in self._pending:
+                self._pending[id(pin)] += delta
+
+    def _access(self, node: Node, net_no: int) -> float:
+        """Extra cost for ``net_no`` to use a cell another pin still needs."""
+        for pin_id, owner_net in self._doorways.get(node, ()):
+            if owner_net != net_no and self._pending.get(pin_id, 0) > 0:
+                return self.access_cost
+        return 0.0
+
     # --- passes -------------------------------------------------------------
 
     def route(self) -> RouteResult:
@@ -819,15 +1144,21 @@ class GridRouter:
         self._conns = conns
         if not conns:
             return RouteResult(self.half_width)
+        if self.access_cost:
+            self._build_doorways(conns)
 
         passes = self.max_passes if self.rip_up else 1
         best_count = -1
         best_snapshot: list[tuple[int, list, list]] | None = None
         best_unrouted = len(conns)
+        best_widths: tuple[dict[int, int], list] = ({}, [])
         # conns[i].index == i is what rip-up relies on, so shuffle a view
         order = list(conns)
         if self.seed is not None:
             random.Random(self.seed).shuffle(order)
+        if self.route_first:
+            # stable: the promoted keep their order among themselves, as do the rest
+            order.sort(key=lambda c: (c.net_no, *_ends_of(c)) not in self.route_first)
         for _ in range(passes):
             changed = False
             for conn in order:
@@ -840,13 +1171,25 @@ class GridRouter:
                 best_count = routed_count
                 best_unrouted = len(conns) - routed_count
                 best_snapshot = self._snapshot(conns)
+                best_widths = self._net_widths(conns)
             if routed_count == len(conns):
                 break
             if not changed:
                 break
-        return self._result_from(best_snapshot or [], best_unrouted)
+        result = self._result_from(best_snapshot or [], best_unrouted)
+        result.net_half, result.narrowed = best_widths
+        return result
 
     def _try_route(self, conn: _Connection, conns: list[_Connection]) -> bool:
+        if self._route_once(conn, conns):
+            return True
+        if conn.narrow or conn.net_no not in self._net_half:
+            return False
+        # a wider class that does not fit: route it at the default width
+        conn.narrow = True
+        return self._route_once(conn, conns)
+
+    def _route_once(self, conn: _Connection, conns: list[_Connection]) -> bool:
         path = self._search(conn, allow_ripup=False, conns=conns)
         if path is None:
             if not self.rip_up:
@@ -854,11 +1197,41 @@ class GridRouter:
             path = self._search(conn, allow_ripup=True, conns=conns)
             if path is None:
                 return False
-            for idx in sorted(self._crossed_owners(path, conn.net_no, conns)):
-                self._rip(conns[idx])
+            victims = [conns[i] for i in sorted(self._crossed_owners(path, conn.net_no, conns))]
+            if self.rollback:
+                return self._ripup_transaction(conn, path, victims, conns)
+            for victim in victims:
+                self._rip(victim)
         self._commit(conn, path)
         return True
 
+    def _ripup_transaction(self, conn, path, victims, conns) -> bool:
+        """Route ``conn`` through ``victims``, reroute them at once in free
+        space, and undo it all if fewer connections end up routed."""
+        saved = [(v, v.path, v.a_end, v.b_end, v.rip_count) for v in victims]
+        own_rips = conn.rip_count
+        for victim in victims:
+            self._rip(victim)
+        self._commit(conn, path)
+        rerouted = 0
+        for victim in victims:
+            again = self._search(victim, allow_ripup=False, conns=conns)
+            if again is not None:
+                self._commit(victim, again)
+                rerouted += 1
+        if 1 + rerouted >= len(victims):
+            return True  # a gain, or an even trade that may pay off later
+        for victim in victims:
+            if victim.routed:
+                self._rip(victim)
+        self._rip(conn)
+        conn.rip_count = own_rips
+        for victim, old_path, a_end, b_end, rips in saved:
+            victim.a_end, victim.b_end = a_end, b_end
+            self._commit(victim, old_path)
+            victim.rip_count = rips
+        return False
+
     def _build_connections(self) -> list[_Connection]:
         pins_by_net = self._pins_by_net()
         zones_by_net: dict[int, list] = {}
@@ -880,7 +1253,9 @@ class GridRouter:
         # deterministic: fewer-pin nets first, then by net number
         for net_no in sorted(nets, key=lambda n: (len(pins_by_net.get(n, [])), n)):
             zones = zones_by_net.get(net_no, []) + planes_by_net.get(net_no, [])
-            groups = _connected_groups(pins_by_net.get(net_no, []), zones, plane_ids)
+            groups = _connected_groups(
+                pins_by_net.get(net_no, []), zones, plane_ids, self._fixed_pieces(net_no)
+            )
             hubs = [g for g in groups if any(id(z) in plane_ids for z in g[1])]
             if hubs:
                 # a plane net: every other group goes straight to the plane
@@ -894,6 +1269,28 @@ class GridRouter:
                 conns.append(conn)
         return conns
 
+    def _fixed_pieces(self, net_no: int) -> list[_FixedPiece]:
+        """The net's tracks and vias already on the board, as connectivity."""
+        cache = getattr(self, "_fixed_cache", None)
+        if cache is None:
+            from freeroute.board.items import Trace
+            from freeroute.geometry.polyline import Polyline, PolylineShape, corner_box
+
+            cache = self._fixed_cache = {}
+            for item in self.board.get_items():
+                if not item.fixed or not item.net_nos:
+                    continue
+                if isinstance(item, Via) and item.shape is not None:
+                    piece = _FixedPiece(item.layers, [item.shape.bounding_box()], via=item)
+                elif isinstance(item, Trace) and not item.is_empty():
+                    boxes = list(PolylineShape(Polyline(item.corners), item.half_width).tiles())
+                    boxes += [corner_box(e, item.half_width) for e in (item.corners[0], item.corners[-1])]
+                    piece = _FixedPiece([item.layer], boxes)
+                else:
+                    continue
+                cache.setdefault(item.net_nos[0], []).append(piece)
+        return cache.get(net_no, [])
+
     def _pins_by_net(self) -> dict[int, list[Pin]]:
         by_net: dict[int, list[Pin]] = {}
         for pin in self.board.get_pins():
@@ -903,6 +1300,21 @@ class GridRouter:
                 by_net.setdefault(net_no, []).append(pin)
         return by_net
 
+    def _net_widths(self, conns: list[_Connection]) -> tuple[dict[int, int], list]:
+        """Half width of each wider-class net whose routed connections all went
+        in at it (a net is written at one width), and the connections that
+        had to fall back to the default."""
+        halves: dict[int, int] = {}
+        narrowed = []
+        for c in conns:
+            if not c.routed:
+                continue
+            halves[c.net_no] = min(halves.get(c.net_no, c.half), c.half)
+            if c.narrow:
+                narrowed.append((c.net_no, *_ends_of(c)))
+        wide = {net: half for net, half in halves.items() if half > self.half_width}
+        return wide, narrowed
+
     def _snapshot(self, conns: list[_Connection]) -> list[tuple]:
         return [
             (c.net_no, [(layer, list(pts)) for layer, pts in c.wires], list(c.vias),
@@ -913,11 +1325,16 @@ class GridRouter:
 
     def _result_from(self, snapshot, unrouted: int) -> RouteResult:
         result = RouteResult(self.half_width)
+        written: set[tuple[int, IntPoint]] = set()
         result.unrouted = unrouted
         for net_no, wires, vias, ends in snapshot:
             for layer, points in wires:
                 result.add_wire(net_no, layer, points)
             for location in vias:
+                spot = (net_no, location)
+                if spot in written or spot in self._fixed_via_points:
+                    continue  # a via reused by another connection, or already on the board
+                written.add(spot)
                 result.add_via(net_no, location)
             result.connections.append((net_no, wires, vias))
             result.connection_ends.append(ends)
@@ -968,13 +1385,49 @@ def _pin_touches_zone(pin: Pin, zone, plane: bool = False) -> bool:
     return any(zone.polygon.contains(c) for c in corners)
 
 
+def _touches(a: IntBox, b: IntBox) -> bool:
+    return not (a.ur.x < b.ll.x or b.ur.x < a.ll.x or a.ur.y < b.ll.y or b.ur.y < a.ll.y)
+
+
+def _fixed_joins_zone(piece, zone, plane: bool) -> bool:
+    """A through via inside a plane joins it; copper inside a zone on its
+    own layer joins that zone."""
+    if zone.polygon is None:
+        return False
+    if piece.via is not None:
+        if plane or zone.layer in piece.layers:
+            return zone.polygon.contains(piece.via.location)
+        return False
+    return zone.layer in piece.layers and any(
+        zone.polygon.contains(IntPoint((b.ll.x + b.ur.x) // 2, (b.ll.y + b.ur.y) // 2))
+        for b in piece.boxes
+    )
+
+
+class _FixedPiece:
+    """One track or via already on the board, as connectivity."""
+
+    __slots__ = ("layers", "boxes", "via")
+
+    def __init__(self, layers, boxes, via=None) -> None:
+        self.layers = frozenset(layers)
+        self.boxes = boxes
+        self.via = via  # the Via item, for a via
+
+
 def _connected_groups(
-    pins: list[Pin], zones: list, planes: frozenset = frozenset()
+    pins: list[Pin], zones: list, planes: frozenset = frozenset(), fixed: list | None = None
 ) -> list[tuple[list[Pin], list]]:
     """Pins and zones of one net that copper already joins: a pad in a zone
-    is connected to it, and two zones sharing a pad are one. Only the groups
-    need routing between them. Pin groups come first, in pin order."""
-    parent = list(range(len(pins) + len(zones)))
+    is connected to it, two zones sharing a pad are one, and copper already
+    on the board (tracks and vias, ``fixed``) joins whatever it touches. Only
+    the groups need routing between them. Pin groups come first, in pin
+    order. A group's fixed vias join its pins as extra route ends, so a
+    fanned-out pin is routed from its via; copper that touches no pin and no
+    zone adds nothing to route."""
+    fixed = fixed or []
+    n_pins, n_zones = len(pins), len(zones)
+    parent = list(range(n_pins + n_zones + len(fixed)))
 
     def find(i: int) -> int:
         while parent[i] != i:
@@ -986,6 +1439,24 @@ def _connected_groups(
         for i, pin in enumerate(pins):
             if _pin_touches_zone(pin, zone, id(zone) in planes):
                 parent[find(i)] = find(len(pins) + j)
+    base = n_pins + n_zones
+    for k, piece in enumerate(fixed):
+        me = base + k
+        for i, pin in enumerate(pins):
+            if pin.shape is None or not piece.layers & set(pin.layers):
+                continue
+            pad = pin.shape.bounding_box()
+            if any(_touches(pad, b) for b in piece.boxes):
+                parent[find(i)] = find(me)
+        for j, zone in enumerate(zones):
+            if _fixed_joins_zone(piece, zone, id(zone) in planes):
+                parent[find(n_pins + j)] = find(me)
+        for k2 in range(k):
+            other = fixed[k2]
+            if piece.layers & other.layers and any(
+                _touches(a, b) for a in piece.boxes for b in other.boxes
+            ):
+                parent[find(base + k2)] = find(me)
     groups: dict[int, tuple[list[Pin], list]] = {}
     order: list[int] = []
     for i, pin in enumerate(pins):
@@ -1000,9 +1471,22 @@ def _connected_groups(
             groups[root] = ([], [])
             order.append(root)
         groups[root][1].append(zone)
+    for k, piece in enumerate(fixed):
+        root = find(base + k)
+        if piece.via is not None and root in groups:
+            groups[root][0].append(_via_end(piece.via))
     return [groups[r] for r in order]
 
 
+def _via_end(via) -> Pin:
+    """A fixed via as a place a route may start or end (not a pad to route)."""
+    return Pin(
+        net_nos=list(via.net_nos), fixed=True, name="via", component_ref="",
+        padstack_name=via.padstack_name, location=via.location,
+        layers=list(via.layers), shape=via.shape,
+    )
+
+
 def _split_path(path: list[Node]) -> tuple[list[tuple[int, list[Cell]]], list[Cell]]:
     """Split a node path into per-layer wire segments and via cells."""
     wires: list[tuple[int, list[Cell]]] = []
@@ -1060,6 +1544,12 @@ def route_board(
     resolution: int = 1,
     heuristic_weight: float = 1.0,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    rollback: bool = True,
+    net_widths: dict[int, int] | None = None,
+    via_drill: int | None = None,
+    hole_to_hole: int = 0,
 ) -> RouteResult:
     """Convenience wrapper: build a :class:`GridRouter` and route the board."""
     router = GridRouter(
@@ -1076,5 +1566,11 @@ def route_board(
         resolution=resolution,
         heuristic_weight=heuristic_weight,
         seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        rollback=rollback,
+        net_widths=net_widths,
+        via_drill=via_drill,
+        hole_to_hole=hole_to_hole,
     )
     return router.route()

src/freeroute/route/orders.py

@@ -65,3 +65,34 @@ def best_of_orders(
     scores = [score(r) for r in results]
     best = min(range(len(seeds)), key=lambda i: (scores[i], i))
     return results[best], seeds[best], list(zip(seeds, scores, strict=True))
+
+
+def promote_failures(
+    dsn_text: str,
+    engine: str,
+    options: dict,
+    *,
+    rounds: int,
+    seed: int | None = None,
+) -> tuple[RoutingResult, list[tuple[int, int]]]:
+    """Route, then route again with every connection that has failed so far
+    moved to the front, keeping the rest in their order. Returns the best
+    round's result and every round's score.
+
+    The promoted set only grows, so a connection that failed once keeps its
+    early place and two groups cannot take turns failing. Stops early when a
+    round routes everything or fails nothing new."""
+    numbers = {n.name: i + 1 for i, n in enumerate(parse_dsn(dsn_text).nets)}
+    first: frozenset = frozenset()
+    best: RoutingResult | None = None
+    scores: list[tuple[int, int]] = []
+    for _ in range(max(int(rounds), 1)):
+        result = route_once(dsn_text, engine, {**options, "route_first": first}, seed)
+        scores.append(score(result))
+        if best is None or scores[-1] < score(best):
+            best = result
+        failed = {(numbers.get(name), a, b) for name, a, b, zone in result.unrouted if not zone}
+        if not failed or failed <= first:
+            break
+        first = first | failed
+    return best, scores

src/freeroute/route/pipeline.py

@@ -12,6 +12,8 @@ to DSN units (dividing by the resolution) for the SES ``(wire (path ...))`` and
 
 from __future__ import annotations
 
+import re
+
 from freeroute.board import build_board
 from freeroute.dsn import DsnBoard, parse_dsn
 from freeroute.ses import RoutedVia, RoutedWire, RoutingResult, write_ses
@@ -34,6 +36,25 @@ def _rule_width_dsn(dsn: DsnBoard) -> float:
     return rules[0].value if rules else _DEFAULT_WIDTH_DSN
 
 
+def _net_widths_board(dsn: DsnBoard, scale: int) -> dict[int, int]:
+    """Track width of every net whose class asks for more than the default,
+    in board units, by net number (build_board numbers nets in DSN order)."""
+    default = _rule_width_dsn(dsn)
+    by_name: dict[str, float] = {}
+    for net_class in dsn.net_classes:
+        if not net_class.width_rules:
+            continue
+        width = net_class.width_rules[0].value
+        if width > default:
+            for name in net_class.net_names:
+                by_name[name] = max(by_name.get(name, 0.0), width)
+    return {
+        i + 1: round(by_name[net.name] * scale)
+        for i, net in enumerate(dsn.nets)
+        if net.name in by_name
+    }
+
+
 def _rule_clearance_dsn(dsn: DsnBoard) -> float:
     for rule in dsn.structure_rules.clearance_rules:
         if not rule.class_pairs:  # the layer-wide default clearance
@@ -53,6 +74,20 @@ def _mm_to_board(dsn: DsnBoard, scale: int, value_mm: float | None) -> int | Non
     return round(value_mm / unit_mm * scale)
 
 
+def _via_drill_board(dsn: DsnBoard, scale: int) -> int | None:
+    """The via's drill in board units, from KiCad's padstack name
+    (``Via[0-1]_600:300_um`` is a 600 um pad with a 300 um drill); None when
+    the name does not say, and the pad size stands in for it."""
+    match = re.search(r"_([\d.]+):([\d.]+)_um", _via_padstack(dsn))
+    if not match:
+        return None
+    return round(float(match.group(2)) * _dsn_units_per_um(dsn) * scale)
+
+
+def _dsn_units_per_um(dsn: DsnBoard) -> float:
+    return {"um": 1.0, "mm": 0.001, "mil": 1 / 25.4, "inch": 1 / 25400}.get(dsn.unit, 1.0)
+
+
 def _via_half_board(dsn: DsnBoard, scale: int) -> int | None:
     """Half the via pad's size in board units, from the DSN's via padstack.
 
@@ -81,6 +116,10 @@ def route_dsn_board(
     rip_up: bool = True,
     max_passes: int = 10,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    hole_to_hole_mm: float = 0.25,
+    rollback: bool = True,
 ) -> tuple[RouteResult, int, list[str]]:
     """Route a parsed :class:`DsnBoard`; return the board-unit result, the scale,
     and the layer names. ``layers`` restricts routing to those signal-layer
@@ -102,6 +141,12 @@ def route_dsn_board(
         rip_up=rip_up,
         max_passes=max_passes,
         seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        rollback=rollback,
+        net_widths=_net_widths_board(dsn, scale),
+        via_drill=_via_drill_board(dsn, scale),
+        hole_to_hole=_mm_to_board(dsn, scale, hole_to_hole_mm) or 0,
     )
     return result, scale, [layer.name for layer in dsn.layers]
 
@@ -116,6 +161,9 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
     result = RoutingResult()
     for net_no, segments in route.wires.items():
         name = numbers_to_names.get(net_no, str(net_no))
+        # its class's width when every connection of the net went in at it
+        half = getattr(route, "net_half", {}).get(net_no)
+        net_width = 2 * half / scale if half else width_dsn
         for layer_index, path in segments:
             layer_name = layer_names[layer_index] if layer_index < len(layer_names) else "F.Cu"
             coords: list[float] = []
@@ -123,7 +171,7 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
                 coords.append(point.x / scale)
                 coords.append(point.y / scale)
             if len(coords) >= 4:
-                result.add_wire(name, RoutedWire(layer=layer_name, width=width_dsn, coords=coords))
+                result.add_wire(name, RoutedWire(layer=layer_name, width=net_width, coords=coords))
     for net_no, locations in route.vias.items():
         name = numbers_to_names.get(net_no, str(net_no))
         for loc in locations:
@@ -131,6 +179,9 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
     result.unrouted = [
         (numbers_to_names.get(n, str(n)), a, b, zone) for n, a, b, zone in getattr(route, "failed", [])
     ]
+    result.narrowed = [
+        (numbers_to_names.get(n, str(n)), a, b) for n, a, b in getattr(route, "narrowed", [])
+    ]
     return result
 
 
@@ -143,11 +194,19 @@ def build_routing_result(
     max_passes: int = 10,
     edge_clearance_mm: float | None = None,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    hole_to_hole_mm: float = 0.25,
+    rollback: bool = True,
 ) -> RoutingResult:
     """Route ``dsn`` (grid track) and convert to a DSN-unit RoutingResult."""
     route, scale, layer_names = route_dsn_board(
         dsn, layers=layers, rip_up=rip_up, max_passes=max_passes,
         edge_clearance_mm=edge_clearance_mm, resolution=resolution, seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        hole_to_hole_mm=hole_to_hole_mm,
+        rollback=rollback,
     )
     return _to_routing_result(route, dsn, scale, layer_names)
 
@@ -164,6 +223,10 @@ def route_dsn_board_exact(
     shove: bool = False,
     diagonal: bool = False,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    hole_to_hole_mm: float = 0.25,
+    rollback: bool = True,
 ) -> tuple[ExactRouteResult, int, list[str]]:
     """Route a parsed :class:`DsnBoard` with the exact-geometry (orthogonal,
     DRC-verified) track; return the exact result, the scale, and layer names.
@@ -189,6 +252,12 @@ def route_dsn_board_exact(
         shove=shove,
         diagonal=diagonal,
         seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        rollback=rollback,
+        net_widths=_net_widths_board(dsn, scale),
+        via_drill=_via_drill_board(dsn, scale),
+        hole_to_hole=_mm_to_board(dsn, scale, hole_to_hole_mm) or 0,
     )
     return exact, scale, [layer.name for layer in dsn.layers]
 
@@ -205,6 +274,10 @@ def build_exact_routing_result(
     max_passes: int = 10,
     edge_clearance_mm: float | None = None,
     seed: int | None = None,
+    route_first: frozenset | None = None,
+    access_cost: float = 0.0,
+    hole_to_hole_mm: float = 0.25,
+    rollback: bool = True,
 ) -> RoutingResult:
     """Route ``dsn`` (exact track) and convert to a DSN-unit RoutingResult."""
     exact, scale, layer_names = route_dsn_board_exact(
@@ -218,6 +291,10 @@ def build_exact_routing_result(
         resolution=resolution,
         heuristic_weight=heuristic_weight,
         seed=seed,
+        route_first=route_first,
+        access_cost=access_cost,
+        hole_to_hole_mm=hole_to_hole_mm,
+        rollback=rollback,
     )
     return _to_routing_result(exact.result, dsn, scale, layer_names)
 

src/freeroute/route/room_router.py

@@ -515,6 +515,10 @@ def route_board_rooms(
         pin_layers = frozenset(layer for layer in pin.layers if layer in signal_layers)
         if pin_layers:
             tree.insert(TreeShape(next(owner), net, pin_layers, box))
+    for net, copper_layers, box in board.get_fixed_copper():
+        on = frozenset(layer for layer in copper_layers if layer in signal_layers)
+        if on and not box.is_empty():
+            tree.insert(TreeShape(next(owner), net, on, box))
     for obstacle in board.get_obstacle_areas():
         if obstacle.layer not in signal_layers:
             continue

src/freeroute/ses/model.py

@@ -60,6 +60,9 @@ class RoutingResult:
     #: connections the router could not make: (net name, one end, other end,
     #: the zone both ends sit in or "") -- a zone's fill may join the latter
     unrouted: list[tuple[str, str, str, str]] = field(default_factory=list)
+    #: connections of a wider net class that only fitted at the default width
+    #: (net name, one end, other end); their net is written at the default
+    narrowed: list[tuple[str, str, str]] = field(default_factory=list)
 
     def net(self, name: str, *, create: bool = False) -> RoutedNet | None:
         """Return the :class:`RoutedNet` with ``name`` (creating it if asked)."""

tests/board/test_build.py

@@ -254,3 +254,37 @@ def test_via_size_comes_from_the_via_padstack():
     from freeroute.route.pipeline import _via_half_board
 
     assert _via_half_board(parse_dsn(_PAD_DSN), 10) == 3000   # 0.6 mm via, board units
+
+
+# --- rule areas: overlap only ------------------------------------------------
+
+_CHANNEL_DSN = """(pcb channel.dsn
+  (parser (string_quote ")) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  40000 0  40000 -30000  0 -30000  0 0))
+    (keepout "{name}top" (polygon signal 0  18000 0  22000 0  22000 -14750  18000 -14750))
+    (keepout "{name}bottom" (polygon signal 0  18000 -15250  22000 -15250  22000 -30000  18000 -30000))
+    (rule (width 250) (clearance 150)))
+  (placement (component P (place P1 5000 -15000 front 0) (place P2 35000 -15000 front 0)))
+  (library (image P (pin pad 1 0 0)) (padstack pad (shape (circle F.Cu 600)) (attach off)))
+  (network (net N (pins P1-1 P2-1))))"""
+
+
+def test_a_keepout_named_rule_area_takes_no_clearance():
+    named = _areas(_CHANNEL_DSN.format(name="rule_area_"))
+    plain = _areas(_CHANNEL_DSN.format(name=""))
+    assert named and not any(a.clearance for a in named)
+    assert plain and all(a.clearance for a in plain)
+
+
+def _route_channel(name):
+    from freeroute.route.pipeline import build_exact_routing_result
+
+    return build_exact_routing_result(parse_dsn(_CHANNEL_DSN.format(name=name)), resolution=2)
+
+
+def test_a_trace_may_run_beside_a_rule_area_closer_than_clearance():
+    # the 0.5 mm channel fits a 0.25 mm trace, but not with 0.15 mm each side
+    assert _route_channel("rule_area_").unrouted == []
+    assert _route_channel("").unrouted != []

tests/board/test_search_tree.py

@@ -62,3 +62,37 @@ def test_has_violation_ignores_static_pad_pairs():
     # a routed trace of net 3 within clearance of pad net 1 -> violation
     tree.insert(shape(2, 3, 0, IntBox(11, 0, 20, 10), routed=True))
     assert tree.has_violation(clearance=20) is not None
+
+
+def test_a_rule_area_conflicts_only_on_overlap():
+    tree = ShapeSearchTree()
+    tree.insert(TreeShape(1, -1, frozenset({0}), IntBox(100, 0, 200, 100), clearance=False))
+    near = IntBox(0, 0, 95, 100)  # 5 short of the area, well inside clearance 50
+    over = IntBox(0, 0, 105, 100)
+    assert not tree.clearance_conflict(near, 7, 0, 50)
+    assert tree.clearance_conflict(over, 7, 0, 50)
+
+
+def test_an_ordinary_keepout_still_needs_clearance():
+    tree = ShapeSearchTree()
+    tree.insert(TreeShape(1, -1, frozenset({0}), IntBox(100, 0, 200, 100)))
+    assert tree.clearance_conflict(IntBox(0, 0, 95, 100), 7, 0, 50)
+
+
+def test_the_routed_board_check_treats_a_rule_area_the_same_way():
+    tree = ShapeSearchTree()
+    tree.insert(TreeShape(1, -1, frozenset({0}), IntBox(100, 0, 200, 100), clearance=False))
+    tree.insert(TreeShape(2, 7, frozenset({0}), IntBox(0, 0, 95, 100), routed=True))
+    assert tree.has_violation(50) is None
+    tree.insert(TreeShape(3, 7, frozenset({0}), IntBox(150, 0, 160, 100), routed=True))
+    assert tree.has_violation(50) is not None
+
+
+
+def test_rule_area_overlap_sees_only_rule_areas():
+    tree = ShapeSearchTree()
+    tree.insert(TreeShape(1, -1, frozenset({0}), IntBox(100, 0, 200, 100), clearance=False))
+    tree.insert(TreeShape(2, -1, frozenset({0}), IntBox(300, 0, 400, 100)))
+    assert tree.rule_area_overlap(IntBox(90, 40, 110, 60), 0)
+    assert not tree.rule_area_overlap(IntBox(290, 40, 310, 60), 0)
+    assert not tree.rule_area_overlap(IntBox(90, 40, 110, 60), 1)

tests/dsn/test_reader.py

@@ -156,3 +156,26 @@ def test_unplaced_component_has_no_coords():
     place = board.placements[0].places[0]
     assert place.name == "U9"
     assert place.x is None and place.y is None
+
+
+# --- string_quote ----------------------------------------------------------
+
+_QUOTED = """(pcb q.dsn
+  (parser (string_quote {q}) (space_in_quoted_tokens on))
+  (resolution um 10) (unit um)
+  (structure (layer F.Cu (type signal)) (boundary (path pcb 0 0 0 1000 0 1000 1000 0 1000 0 0)))
+  (placement (component "SW1" (place SW1 100 100 front 0 (PN {pn}))))
+  (library)
+  (network)
+)"""
+
+
+def test_a_bare_apostrophe_is_an_atom_when_the_file_quotes_with_double_quotes():
+    # KiCad declares " and writes a keycap's part number as a bare '
+    board = parse_dsn(_QUOTED.format(q='"', pn="'"))
+    assert board.parser.string_quote == '"'
+
+
+def test_the_declared_quote_character_is_the_one_that_opens_strings():
+    board = parse_dsn(_QUOTED.format(q="'", pn="'10k 1%'").replace('"SW1"', "'SW1'"))
+    assert board.parser.string_quote == "'"

tests/route/test_fixed_wiring.py

@@ -0,0 +1,93 @@
+"""Tracks and vias already on the board (the DSN's wiring) are fixed copper."""
+
+from __future__ import annotations
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import route_dsn_board_exact
+
+_DSN = """(pcb wired (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  30000 0  30000 -20000  0 -20000  0 0))
+    (via "Via[0-1]_600:300_um") (rule (width 250) (clearance 200)))
+  (placement (component S (place A1 5000 -10000 front 0) (place A2 25000 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -400 -400 400 400)) (attach off))
+    (padstack "Via[0-1]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net SIG (pins A1-1 A2-1)) (net GND))
+  (wiring
+    (wire (path F.Cu 400  15000 0  15000 -20000) (net GND) (type route))
+    (via "Via[0-1]_600:300_um"  8000 -14000 (net GND) (type route))))"""
+
+
+def test_wiring_is_read_with_its_nets():
+    dsn = parse_dsn(_DSN)
+    assert [(w.net, w.layer, w.width) for w in dsn.wires] == [("GND", "F.Cu", 400.0)]
+    assert [(v.net, v.x, v.y) for v in dsn.vias] == [("GND", 8000.0, -14000.0)]
+
+
+def test_wiring_is_fixed_copper_and_not_a_connection_to_route():
+    board = build_board(parse_dsn(_DSN))
+    copper = board.get_fixed_copper()
+    gnd = next(n.net_number for n in board.nets if n.name == "GND")
+    assert copper and all(net == gnd for net, _, _ in copper)
+    assert not any(gnd in p.net_nos for p in board.get_pins())
+
+
+def test_other_nets_route_around_a_fixed_track():
+    dsn = parse_dsn(_DSN)
+    exact, scale, names = route_dsn_board_exact(dsn, resolution=2)
+    sig = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "SIG")
+    assert sig in exact.result.routed_net_numbers
+    assert exact.drc_clean
+    wall = 15000 * scale
+    for layer, pts in exact.result.wires.get(sig, []):
+        if names[layer] != "F.Cu":
+            continue
+        for p, q in zip(pts, pts[1:], strict=False):
+            assert not (min(p.x, q.x) < wall < max(p.x, q.x)), "crossed the GND track on F.Cu"
+
+
+# --- fixed wiring as connectivity ------------------------------------------
+
+_FANOUT = """(pcb fanout (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  30000 0  30000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  29500 -500  29500 -19500  500 -19500  500 -500))
+    (via "Via[0-3]_600:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 5000 -10000 front 0) (place A 10000 -10000 front 0)
+                          (place B 25000 -11500 back 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -300 -300 300 300)) (attach off))
+    (padstack "Via[0-3]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net GND (pins G1-1)) (net SIG (pins A-1 B-1)))
+  (wiring
+    (wire (path F.Cu 150  5000 -10000  5000 -11500) (net GND) (type route))
+    (via "Via[0-3]_600:300_um"  5000 -11500 (net GND) (type route))
+    (wire (path F.Cu 150  10000 -10000  10000 -11500) (net SIG) (type route))
+    (via "Via[0-3]_600:300_um"  10000 -11500 (net SIG) (type route))
+    (wire (path F.Cu 300  2000 -2000  8000 -2000) (net GND) (type route))))"""
+
+
+def test_a_pad_fanned_out_to_its_plane_needs_no_route():
+    dsn = parse_dsn(_FANOUT)
+    exact, _scale, _names = route_dsn_board_exact(dsn, resolution=2)
+    gnd = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "GND")
+    assert exact.result.failed == []
+    assert not exact.result.vias.get(gnd) and not exact.result.wires.get(gnd)
+
+
+def test_a_fanned_out_signal_is_routed_from_its_via():
+    # B is on the bottom face, level with A's fan-out via: starting from that
+    # via on B.Cu is the cheapest way, and needs no via of its own
+    dsn = parse_dsn(_FANOUT)
+    exact, scale, names = route_dsn_board_exact(dsn, resolution=2)
+    sig = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "SIG")
+    assert sig in exact.result.routed_net_numbers
+    assert not exact.result.vias.get(sig), "the fan-out via is already there"
+    assert {names[layer] for layer, _ in exact.result.wires[sig]} == {"B.Cu"}

tests/route/test_net_widths.py

@@ -0,0 +1,42 @@
+"""Net classes wider than the default are routed at their width where it fits."""
+
+from __future__ import annotations
+
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import build_exact_routing_result
+
+_BOARD = """(pcb widths (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -10000  0 -10000  0 0))
+    {keepouts}
+    (rule (width 150) (clearance 150)))
+  (placement (component S (place P1 2000 -5000 front 0) (place P2 18000 -5000 front 0)))
+  (library (image S (pin pad 1 0 0)) (padstack pad (shape (rect F.Cu -600 -600 600 600)) (attach off)))
+  (network (net PWR (pins P1-1 P2-1))
+    (class Power PWR (rule (width 400) (clearance 150)))))"""
+
+# two keepouts leave a 0.65 mm channel: room for 0.15 mm (0.45), not for 0.4 mm (0.7)
+_CHANNEL = (
+    '(keepout "" (polygon F.Cu 0  9000 0  11000 0  11000 -4675  9000 -4675))\n'
+    '    (keepout "" (polygon F.Cu 0  9000 -5325  11000 -5325  11000 -10000  9000 -10000))'
+)
+
+
+def _route(keepouts=""):
+    return build_exact_routing_result(parse_dsn(_BOARD.format(keepouts=keepouts)), resolution=2)
+
+
+def test_a_wider_class_is_routed_and_written_at_its_width():
+    result = _route()
+    assert result.unrouted == [] and result.narrowed == []
+    widths = {w.width for net in result.nets for w in net.wires}
+    assert widths == {400.0}
+
+
+def test_a_wider_class_that_does_not_fit_falls_back_to_the_default():
+    result = _route(_CHANNEL)
+    assert result.unrouted == []
+    assert [net for net, _a, _b in result.narrowed] == ["PWR"]
+    widths = {w.width for net in result.nets for w in net.wires}
+    assert widths == {150.0}

tests/route/test_orders.py

@@ -5,7 +5,13 @@ from __future__ import annotations
 from pathlib import Path
 
 from freeroute.cli import main
-from freeroute.route.orders import best_of_orders, candidate_seeds, route_once, score
+from freeroute.route.orders import (
+    best_of_orders,
+    candidate_seeds,
+    promote_failures,
+    route_once,
+    score,
+)
 
 FIXTURES = Path(__file__).resolve().parent.parent / "dsn" / "fixtures"
 # Greedy (no rip-up), the default order strands a net here and seeds 1 to 3 do not.
@@ -42,3 +48,31 @@ def test_cli_orders_writes_the_best_session(tmp_path, capsys):
     assert "tried 3 orders, kept --seed 1" in err
     assert "not routed" not in err
     assert out.read_text().startswith("(session")
+
+
+def test_promoting_the_failed_connection_routes_it():
+    best, rounds = promote_failures(RIPUP, "grid", GREEDY, rounds=3)
+    assert rounds == [(1, 0), (0, 0)]  # stops once nothing fails
+    assert score(best) == (0, 0)
+
+
+def test_nothing_promoted_is_the_plain_order():
+    plain = route_once(RIPUP, "grid", {}, None)
+    empty = route_once(RIPUP, "grid", {"route_first": frozenset()}, None)
+    assert plain == empty
+
+
+def test_cli_promote_failures(tmp_path, capsys):
+    out = tmp_path / "p.ses"
+    rc = main(
+        [
+            str(FIXTURES / "ripup_needed.dsn"),
+            "--no-rip-up",
+            "--promote-failures",
+            "3",
+            "-do",
+            str(out),
+        ]
+    )
+    assert rc == 0
+    assert "2 rounds, unrouted 1, 0" in capsys.readouterr().err

tests/route/test_real_board_geometry.py

@@ -202,6 +202,18 @@ def test_smd_pads_reach_an_inner_plane_by_their_own_via():
     assert all(names[layer] in ("F.Cu", "B.Cu") for segs in result.result.wires.values() for layer, _ in segs)
 
 
+def test_a_pad_outside_the_plane_routes_to_it():
+    # G1 sits left of a plane that covers only the right half, so its route
+    # has to reach the plane's cells: those ends are the plane, not a pin
+    dsn_text = _four_layer_dsn().replace(
+        "(plane GND (polygon In1.Cu 0  500 -500  29500 -500  29500 -29500  500 -29500  500 -500))",
+        "(plane GND (polygon In1.Cu 0  15000 -500  29500 -500  29500 -29500  15000 -29500  15000 -500))",
+    )
+    result, _scale, _names = route_dsn_board_exact(parse_dsn(dsn_text))
+    gnd = next(i + 1 for i, n in enumerate(parse_dsn(dsn_text).nets) if n.name == "GND")
+    assert gnd in result.result.routed_net_numbers
+
+
 def test_a_through_hole_pad_inside_a_plane_needs_no_route():
     from freeroute.route.grid_router import _connected_groups
 
@@ -211,3 +223,29 @@ def test_a_through_hole_pad_inside_a_plane_needs_no_route():
     groups = _connected_groups(gnd_pins, plane, frozenset(id(z) for z in plane))
     hub = next(g for g in groups if g[1])
     assert [p.component_ref for p in hub[0]] == ["GT"]
+
+
+def test_a_pad_inside_a_via_keepout_reaches_the_plane_by_a_via_outside_it():
+    # a sensor's GND pad: vias are forbidden under the body, so the route
+    # has to leave on the top layer and drop to the plane past the keepout
+    dsn = parse_dsn("""(pcb repro (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  19500 -500  19500 -19500  500 -19500  500 -500))
+    (via_keepout "" (polygon signal 0  8500 -8500  11500 -8500  11500 -11500  8500 -11500  8500 -8500))
+    (via "Via[0-3]_600:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 10000 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -175 -300 175 300)) (attach off))
+    (padstack "Via[0-3]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net GND (pins G1-1))))""")
+    exact, scale, _names = route_dsn_board_exact(dsn, resolution=2)
+    assert exact.result.failed == []
+    (via,) = exact.result.vias[1]
+    half = 300 * scale  # the via's radius
+    outside = (via.x + half <= 8500 * scale or via.x - half >= 11500 * scale
+               or via.y - half >= -8500 * scale or via.y + half <= -11500 * scale)
+    assert outside, f"via at {via} is inside the via keepout"

tests/route/test_rollback.py

@@ -0,0 +1,43 @@
+"""--rollback: a rip-up that loses connections is undone, leaving no trace."""
+
+from __future__ import annotations
+
+from pathlib import Path
+
+import pytest
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.route.grid_router import GridRouter
+from freeroute.route.pipeline import _rule_clearance_dsn, _rule_width_dsn, route_dsn_board
+
+FIXTURES = Path(__file__).resolve().parent.parent / "dsn" / "fixtures"
+
+
+def _routed_router(name):
+    dsn = parse_dsn((FIXTURES / name).read_text())
+    s = dsn.resolution.value
+    router = GridRouter(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        rollback=True,
+    )
+    return router, router.route()
+
+
+@pytest.mark.parametrize("name", ["ripup_needed.dsn", "true_density.dsn", "kicad_routable.dsn"])
+def test_occupancy_only_holds_routed_connections(name):
+    router, _ = _routed_router(name)
+    conns = router._conns
+    assert all(conns[i].routed for i in router._cell_owner.values())
+    assert all(conns[i].routed for i in router._via_owner.values())
+    assert all(conns[i].routed for claims in router._halo.values() for i in claims)
+
+
+@pytest.mark.parametrize("name", ["ripup_needed.dsn", "true_density.dsn", "kicad_routable.dsn"])
+def test_rollback_never_routes_fewer_than_plain_rip_up(name):
+    text = (FIXTURES / name).read_text()
+    plain, _, _ = route_dsn_board(parse_dsn(text), rollback=False)
+    undo, _, _ = route_dsn_board(parse_dsn(text))
+    assert undo.unrouted <= plain.unrouted

tests/route/test_via_spacing.py

@@ -0,0 +1,56 @@
+"""Vias keep hole-to-hole spacing, even within one net."""
+
+from __future__ import annotations
+
+import itertools
+import math
+
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import route_dsn_board_exact
+
+# four GND pads 0.5 mm apart over a GND plane: each drops a via to the plane
+_DSN = """(pcb holes (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  19500 -500  19500 -19500  500 -19500  500 -500))
+    (via "Via[0-3]_500:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 9000 -10000 front 0) (place G2 9500 -10000 front 0)
+                          (place G3 10000 -10000 front 0) (place G4 10500 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -150 -300 150 300)) (attach off))
+    (padstack "Via[0-3]_500:300_um" (shape (circle F.Cu 500)) (shape (circle B.Cu 500)) (attach off)))
+  (network (net GND (pins G1-1 G2-1 G3-1 G4-1))))"""
+
+
+def test_a_nets_own_vias_keep_hole_to_hole_spacing():
+    dsn = parse_dsn(_DSN)
+    exact, scale, _ = route_dsn_board_exact(dsn, resolution=2)
+    assert exact.result.failed == []
+    vias = exact.result.vias[1]
+    assert len(set(vias)) == len(vias), "a via written twice"
+    need = (300 + 250) * scale  # drill + 0.25 mm, centre to centre
+    for a, b in itertools.combinations(vias, 2):
+        assert math.hypot(a.x - b.x, a.y - b.y) >= need, f"vias at {a} and {b} too close"
+
+
+def test_connections_sharing_a_plane_via_write_it_once():
+    # eight GND pads 0.4 mm apart: the hole spacing makes several of them
+    # end on the same plane via, which must come out once, not once each
+    pads = " ".join(f"(place G{i} {9000 + 400 * i} -10000 front 0)" for i in range(8))
+    pins = " ".join(f"G{i}-1" for i in range(8))
+    dsn = parse_dsn(
+        _DSN.replace(
+            "(place G1 9000 -10000 front 0) (place G2 9500 -10000 front 0)\n"
+            "                          (place G3 10000 -10000 front 0) (place G4 10500 -10000 front 0)",
+            pads,
+        )
+        .replace("(pins G1-1 G2-1 G3-1 G4-1)", f"(pins {pins})")
+        .replace("(rect F.Cu -150 -300 150 300)", "(rect F.Cu -125 -300 125 300)")
+    )
+    exact, _scale, _ = route_dsn_board_exact(dsn, resolution=2)
+    vias = exact.result.vias[1]
+    assert len(vias) < 8, "no via is shared, so this board no longer tests sharing"
+    assert len(set(vias)) == len(vias), "a shared via written more than once"

tests/test_cli.py

@@ -156,6 +156,9 @@ def test_cli_supported_combinations_are_accepted(tmp_path):
         "max_passes": ["-mp", "4"],
         "seed": ["--seed", "3"],
         "orders": ["--orders", "2"],
+        "promote": ["--promote-failures", "2"],
+        "access": ["--access-cost", "5"],
+        "rollback": ["--no-rollback"],
     }
     for engine, options in ENGINE_OPTIONS.items():
         for option in options: