Let pins on turned fine-pitch pads leave along the pad's axis

A QFN placed at 45 degrees had no exit on the grid: every horizontal or
vertical step from a pin passes its neighbours inside clearance. A pin whose
pad is turned more than ten degrees off the grid axes now leaves along the
pad's own axis, away from the part, until an L from there to a grid cell
clears every other net's pad, then searches as usual. The slanted leg is
checked and stored as an exact slab (segment_slab), not its bounding box,
in the grid stub checks and in the exact engine.

Where pins leave side by side, a cell names only its first owner, so stubs
are also indexed per cell for every connection near them; the exact
stub-vs-stub check, trace entry and rip-up all consult that index. A pin
with an axis exit and no clear cell reports no way out instead of falling
back to a cell on another net's route. diagnose.py replays with the exits.

bench/diagnose.py

@@ -32,8 +32,10 @@ from freeroute.route.exact_router import route_board_exact
 from freeroute.route.grid_router import GridRouter, _ends_of
 from freeroute.route.pipeline import (
     _mm_to_board,
+    _net_widths_board,
     _rule_clearance_dsn,
     _rule_width_dsn,
+    _via_drill_board,
     _via_half_board,
 )
 
@@ -106,6 +108,15 @@ def _capture_conflicts() -> list:
     return log
 
 
+def _wall_name(wall, names) -> str:
+    if isinstance(wall, str):
+        if wall.startswith("fixed copper of net "):
+            net = int(wall.rsplit(" ", 1)[1])
+            return f"fixed copper of {names.get(net, net)}"
+        return wall
+    return names.get(wall, "pads/keepouts")
+
+
 def _gap(a, b) -> int:
     dx = max(b.ll.x - a.ur.x, a.ll.x - b.ur.x, 0)
     dy = max(b.ll.y - a.ur.y, a.ll.y - b.ur.y, 0)
@@ -118,6 +129,25 @@ def _fresh(seen) -> GridRouter:
     return router
 
 
+def _static_wall(router: GridRouter, node) -> str:
+    """What static copper closes a node: a keepout, copper already on the
+    board (a fixed via or track, by net), or a pad."""
+    if node in router._keepout:
+        return "keepout"
+    fixed = getattr(router, "_diag_fixed", None)
+    if fixed is None:
+        fixed = router._diag_fixed = {}
+        margin = router.clearance + router.half_width
+        for net, layers, box in router.board.get_fixed_copper():
+            for cell in router._cells_in_box(box, margin):
+                for layer in layers:
+                    fixed[(*cell, layer)] = net
+    net = fixed.get(node)
+    if net is not None:
+        return f"fixed copper of net {net}"
+    return "pads"
+
+
 def _flood(router: GridRouter, pin, net_no: int, conns) -> tuple[int, Counter]:
     """How many nodes a pin can reach through free cells (up to FLOOD_LIMIT),
     and which other nets' copper bounds the region."""
@@ -146,7 +176,7 @@ def _flood(router: GridRouter, pin, net_no: int, conns) -> tuple[int, Counter]:
                 for owner in owners:
                     walls[conns[owner].net_no] += 1
                 if not owners:
-                    walls[0] += 1  # a pad or keepout
+                    walls[_static_wall(router, n)] += 1
                 continue
             seen.add(n)
             frontier.append(n)
@@ -155,7 +185,8 @@ def _flood(router: GridRouter, pin, net_no: int, conns) -> tuple[int, Counter]:
 
 def diagnose(
     dsn_text: str, edge_clearance_mm: float | None, resolution: int = 2, shove: bool = False,
-    access_cost: float = 0.0,
+    access_cost: float = 0.0, hole_to_hole_mm: float = 0.25, seed: int | None = None,
+    negotiate: int = 0,
 ) -> dict:
     dsn = parse_dsn(dsn_text)
     names = {i + 1: n.name for i, n in enumerate(dsn.nets)}
@@ -171,6 +202,12 @@ def diagnose(
         resolution=resolution,
         shove=shove,
         access_cost=access_cost,
+        seed=seed,
+        negotiate=negotiate,
+        # the product's configuration: net-class widths and hole spacing
+        net_widths=_net_widths_board(dsn, scale),
+        via_drill=_via_drill_board(dsn, scale),
+        hole_to_hole=_mm_to_board(dsn, scale, hole_to_hole_mm) or 0,
     )
     routed = seen["router"]
     best = routed._diag_best
@@ -178,6 +215,8 @@ def diagnose(
 
     # the board as the best pass left it
     state = _fresh(seen)
+    # pins on turned pads leave along their pad's axis: replay with the same exits
+    state._axis_exits = dict(routed._axis_exits)
     conns = state._conns
     for idx, (path, a_end, b_end) in best.items():
         conns[idx].a_end, conns[idx].b_end = a_end, b_end
@@ -224,7 +263,9 @@ def diagnose(
                     if reach < FLOOD_LIMIT:
                         walled.append({
                             "pin": end, "reach": reach,
-                            "walls": [names.get(n, "pads/keepouts") for n, _ in walls.most_common(4)],
+                            "walls": [
+                                _wall_name(n, names) for n, _ in walls.most_common(4)
+                            ],
                         })
             row["kind"] = "walled-in" if walled else "congestion"
             if walled:
@@ -240,11 +281,14 @@ def main(argv: list[str] | None = None) -> int:
     ap.add_argument("--grid-resolution", type=int, default=2, metavar="K")
     ap.add_argument("--shove", action="store_true", help="as mckicad routes")
     ap.add_argument("--access-cost", type=float, default=0.0)
+    ap.add_argument("--seed", type=int, help="route in this shuffled order, as bench.py does")
+    ap.add_argument("--negotiate", type=int, default=0, metavar="N", help="as the router's --negotiate")
+    ap.add_argument("--hole-to-hole", type=float, default=0.25, metavar="MM")
     ap.add_argument("--json", type=Path, help="also write the full table here")
     args = ap.parse_args(argv)
 
     report = diagnose(args.dsn.read_text(), args.edge_clearance, args.grid_resolution, args.shove,
-                      args.access_cost)
+                      args.access_cost, args.hole_to_hole, args.seed, args.negotiate)
     for row in report["failures"]:
         extra = ""
         for w in row.get("walled", []):

bench/drc_check.sh

@@ -0,0 +1,67 @@
+#!/usr/bin/env bash
+# Route one KiCad board with freeroute and judge the result with KiCad's DRC.
+#
+#   bench/drc_check.sh [--keep] <board.kicad_pcb> <out-dir> [freeroute args...]
+#
+# Copies the board (and its .kicad_pro) into <out-dir>, strips its tracks and
+# vias unless --keep is given (then they reach the router as fixed wiring),
+# exports the DSN through mckicad, routes, applies the session, and runs DRC
+# with zones refilled at every severity. Prints one line: time, copper added,
+# shorts, opens, hole problems (whatever severity the board gives them) and
+# the other errors. The source board is never touched.
+#
+# FREEROUTE (default: this checkout's .venv/bin/freeroute) and MCK (default
+# ~/claude/mckicad) pick the builds to judge.
+set -euo pipefail
+keep=0
+if [[ "${1:-}" == "--keep" ]]; then keep=1; shift; fi
+src="$1"; out="$2"; shift 2
+here="$(cd "$(dirname "$0")/.." && pwd)"
+FREEROUTE="${FREEROUTE:-$here/.venv/bin/freeroute}"
+MCK="${MCK:-$HOME/claude/mckicad}"
+rm -rf "$out"; mkdir -p "$out"
+cp "${src%.kicad_pcb}.kicad_pro" "$out/board.kicad_pro" 2>/dev/null || true
+
+if [[ $keep == 1 ]]; then
+    cp "$src" "$out/board.kicad_pcb"
+else
+    (cd "$MCK" && uv run --no-sync python - "$src" "$out/board.kicad_pcb" <<'EOF'
+import sys
+from mckicad.utils.sexp_tree import parse
+text = open(sys.argv[1]).read()
+spans = sorted((c.span for c in parse(text).children if c.tag in ("segment", "arc", "via")), reverse=True)
+for a, b in spans:
+    text = text[:a] + text[b:]
+open(sys.argv[2], "w").write(text)
+EOF
+    )
+fi
+
+(cd "$MCK" && uv run --no-sync python -c "
+from mckicad.utils.freerouting import FreeRoutingEngine
+assert FreeRoutingEngine().export_dsn_from_kicad('$out/board.kicad_pcb', '$out/board.dsn', {})") \
+    >/dev/null 2>&1 || { echo "$out: DSN export failed"; exit 1; }
+
+start=$(date +%s.%N)
+"$FREEROUTE" "$out/board.dsn" -do "$out/board.ses" "$@" >"$out/route.log" 2>&1 || true
+secs=$(python3 -c "print(round($(date +%s.%N)-$start,1))")
+[[ -s "$out/board.ses" ]] || { echo "$out: no session ($(tail -1 "$out/route.log"))"; exit 1; }
+
+(cd "$MCK" && uv run --no-sync python -c "
+from mckicad.utils.ses_apply import apply_ses_to_board as a
+r = a('$out/board.kicad_pcb', '$out/board.ses', '$out/board.kicad_pcb')
+print(r['segments_added'], r['vias_added'])" 2>/dev/null) >"$out/apply.txt"
+
+kicad-cli pcb drc --refill-zones --format json --severity-all \
+    -o "$out/drc.json" "$out/board.kicad_pcb" >/dev/null 2>&1 || true
+python3 - "$out" "$secs" <<'EOF'
+import collections, json, sys
+out, secs = sys.argv[1:]
+seg, via = open(f"{out}/apply.txt").read().split()
+d = json.load(open(f"{out}/drc.json"))
+errors = collections.Counter(v["type"] for v in d["violations"] if v.get("severity") == "error")
+other = collections.Counter(v["type"] for v in d["violations"] if v.get("severity") != "error")
+holes = {k: errors.pop(k, 0) + other.get(k, 0) for k in ("holes_co_located", "hole_to_hole")}
+print(f"{out}: {secs}s  {seg} seg {via} via  shorts {errors.pop('shorting_items', 0)}  "
+      f"opens {len(d.get('unconnected_items', []))}  holes {holes}  errors {dict(errors)}")
+EOF

src/freeroute/board/board.py

@@ -70,6 +70,27 @@ class BasicBoard:
     def get_traces(self) -> list[Trace]:
         return [it for it in self._items if isinstance(it, Trace)]
 
+    def get_fixed_copper(self) -> list[tuple[int, frozenset[int], IntBox]]:
+        """Copper already routed on the board (the DSN's ``wiring``), as
+        ``(net, layers, box)``. A track is its segments, its corners and the
+        round caps at its ends (as squares); a via is its largest pad."""
+        from freeroute.geometry.polyline import Polyline, PolylineShape, corner_box
+
+        out: list[tuple[int, frozenset[int], IntBox]] = []
+        for item in self._items:
+            if not item.fixed or not item.net_nos:
+                continue
+            net = item.net_nos[0]
+            if isinstance(item, Trace) and not item.is_empty():
+                layers = frozenset({item.layer})
+                for box in PolylineShape(Polyline(item.corners), item.half_width).tiles():
+                    out.append((net, layers, box))
+                for end in (item.corners[0], item.corners[-1]):
+                    out.append((net, layers, corner_box(end, item.half_width)))
+            elif isinstance(item, Via) and item.shape is not None:
+                out.append((net, frozenset(item.layers), item.shape.bounding_box()))
+        return out
+
     def get_vias(self) -> list[Via]:
         return [it for it in self._items if isinstance(it, Via)]
 

src/freeroute/board/build.py

@@ -12,9 +12,10 @@ model. It mirrors what FreeRouting's ``Structure.create_board`` / ``Library`` /
 * padstacks x placement -> :class:`Pin` items
 * keepouts -> :class:`ObstacleArea` items
 
-Pad geometry: a rectangle pad becomes an exact :class:`IntBox`; a circle pad its
+Pad geometry: a rectangle pad becomes an exact :class:`IntBox`; a circle pad a
-bounding box (documented approximation pending an exact circle tile); a convex
+16-sided :class:`Simplex` drawn just outside it (its corners stand out by 2% of
-polygon pad an exact :class:`Simplex`. Every pad is placed centred on its pin
+the radius, where the bounding box's stood out by 41%); a convex polygon pad an
+exact :class:`Simplex`. Every pad is placed centred on its pin
 location, so it contains that location by construction. Component rotation is
 applied to the pin position; the pad tile itself is not rotated (irrelevant to
 the containment invariant, and pads are centre-symmetric in practice).
@@ -23,6 +24,7 @@ the containment invariant, and pads are centre-symmetric in practice).
 from __future__ import annotations
 
 import math
+import re
 
 from freeroute.dsn.model import DsnBoard
 from freeroute.dsn.shapes import Circle, Path, Polygon, Rectangle, Shape
@@ -31,13 +33,16 @@ from freeroute.geometry.polygon_shape import PolygonShape
 
 from .board import BasicBoard
 from .clearance import ClearanceMatrix
-from .items import ConductionArea, ObstacleArea, Pin
+from .items import ConductionArea, ObstacleArea, Pin, Trace, Via
 from .layer import Layer, LayerStructure
 from .net import Nets
 from .transform import CoordinateTransform
 
 __all__ = ["build_board"]
 
+# DSN units per micrometre, for drills KiCad gives in um in via padstack names
+_DSN_PER_UM = {"um": 1.0, "mm": 0.001, "mil": 1 / 25.4, "inch": 1 / 25400}
+
 
 def build_board(dsn: DsnBoard) -> BasicBoard:
     """Construct a :class:`BasicBoard` from a parsed :class:`DsnBoard`."""
@@ -56,6 +61,7 @@ def build_board(dsn: DsnBoard) -> BasicBoard:
     _insert_keepouts(dsn, board, transform)
     _insert_image_keepouts(dsn, board, transform)
     _insert_zones(dsn, board, transform, nets)
+    _insert_wiring(dsn, board, transform, nets)
     return board
 
 
@@ -244,7 +250,7 @@ def _placed_pad_tile(shape: Shape, place, dsn_pin, transform: CoordinateTransfor
         r = round(transform.dsn_to_board(shape.diameter / 2))
         cx = round(transform.dsn_to_board(centre.x))
         cy = round(transform.dsn_to_board(centre.y))
-        return IntBox(cx - r, cy - r, cx + r, cy + r)
+        return _circle_tile(cx, cy, r)
     if isinstance(shape, Rectangle):
         x0, y0, x1, y1 = shape.coords[:4]
         corners = [(x0, y0), (x1, y0), (x1, y1), (x0, y1)]
@@ -263,15 +269,65 @@ def _placed_pad_tile(shape: Shape, place, dsn_pin, transform: CoordinateTransfor
     for x, y in corners:
         p = _to_board_offset(place, x, y, dsn_pin.rotation)
         pts.append(IntPoint(round(transform.dsn_to_board(p.x)), round(transform.dsn_to_board(p.y))))
-    if len(pts) >= 3:
+    # An oval's padded corners are not in outline order, and a mirrored
-        simplex = Simplex.from_corners(pts)
+    # part reverses the winding: take the convex hull, then either winding.
-        if not simplex.is_empty():
+    hull = _convex_hull(pts)
-            return simplex
+    if len(hull) >= 3:
+        for corners in (hull, hull[::-1]):
+            simplex = Simplex.from_corners(corners)
+            if not simplex.is_empty():
+                return simplex
     xs = [p.x for p in pts] or [0]
     ys = [p.y for p in pts] or [0]
     return IntBox(min(xs), min(ys), max(xs), max(ys))
 
 
+_CIRCLE_SIDES = 16
+
+
+def _circle_tile(cx: int, cy: int, r: int):
+    """A polygon around the circle, every side touching it. A square around a
+    big round pad (a mounting hole) puts phantom copper in its corners that
+    blocks legal routes past it; this stays outside the circle, so the router
+    is still never closer than KiCad measures."""
+    if r < 8:
+        return IntBox(cx - r, cy - r, cx + r, cy + r)
+    reach = r / math.cos(math.pi / _CIRCLE_SIDES)
+    corners = []
+    for k in range(_CIRCLE_SIDES):
+        a = (k + 0.5) * 2 * math.pi / _CIRCLE_SIDES
+        dx, dy = reach * math.cos(a), reach * math.sin(a)
+        # round away from the centre so the polygon never cuts into the circle
+        corners.append(IntPoint(cx + math.copysign(math.ceil(abs(dx)), dx),
+                                cy + math.copysign(math.ceil(abs(dy)), dy)))
+    corners = [IntPoint(int(p.x), int(p.y)) for p in corners]
+    for winding in (corners, corners[::-1]):
+        simplex = Simplex.from_corners(winding)
+        if not simplex.is_empty():
+            return simplex
+    return IntBox(cx - r, cy - r, cx + r, cy + r)
+
+
+def _convex_hull(pts: list[IntPoint]) -> list[IntPoint]:
+    """The convex hull of ``pts`` counter-clockwise, collinear points dropped."""
+    ps = sorted({(p.x, p.y) for p in pts})
+    if len(ps) < 3:
+        return [IntPoint(x, y) for x, y in ps]
+
+    def cross(o, a, b):
+        return (a[0] - o[0]) * (b[1] - o[1]) - (a[1] - o[1]) * (b[0] - o[0])
+
+    def half(points):
+        out: list[tuple[int, int]] = []
+        for p in points:
+            while len(out) >= 2 and cross(out[-2], out[-1], p) <= 0:
+                out.pop()
+            out.append(p)
+        return out[:-1]
+
+    return [IntPoint(x, y) for x, y in half(ps) + half(ps[::-1])]
+
+
 def _pad_tile(shape: Shape, transform: CoordinateTransform):
     """A board-relative pad tile from a DSN padstack shape (centred near origin)."""
     if isinstance(shape, Rectangle):
@@ -281,7 +337,7 @@ def _pad_tile(shape: Shape, transform: CoordinateTransform):
         r = round(transform.dsn_to_board(shape.diameter / 2))
         cx = round(transform.dsn_to_board(shape.center_x))
         cy = round(transform.dsn_to_board(shape.center_y))
-        return IntBox(cx - r, cy - r, cx + r, cy + r)  # bounding-box approximation
+        return _circle_tile(cx, cy, r)
     if isinstance(shape, (Polygon, Path)):
         coords = shape.coords
         pts = [
@@ -471,6 +527,52 @@ def _placed_area_tiles(shape: Shape, place, transform: CoordinateTransform) -> l
     return [tile for tile in PolygonShape(pts).split_to_convex() if not tile.is_empty()]
 
 
+def _insert_wiring(dsn: DsnBoard, board: BasicBoard, transform: CoordinateTransform, nets) -> None:
+    """Tracks and vias already on the board, as fixed copper of their nets."""
+    layer_no = {layer.name: i for i, layer in enumerate(dsn.layers)}
+    signal_layers = [i for i, layer in enumerate(dsn.layers) if layer.is_signal]
+    numbers = {net.name: net.net_number for net in nets}
+    for wire in dsn.wires:
+        if wire.net not in numbers or wire.layer not in layer_no:
+            continue
+        c = wire.coords
+        corners = [transform.dsn_to_board_point(c[i], c[i + 1]) for i in range(0, len(c) - 1, 2)]
+        if len(corners) < 2:
+            continue
+        board.insert(
+            Trace(
+                net_nos=[numbers[wire.net]], fixed=True, layer=layer_no[wire.layer],
+                half_width=max(round(transform.dsn_to_board(wire.width / 2)), 1), corners=corners,
+            )
+        )
+    for via in dsn.vias:
+        padstack = dsn.padstack(via.padstack)
+        if via.net not in numbers or padstack is None or not padstack.shapes:
+            continue
+        layers: set[int] = set()
+        for shape in padstack.shapes:
+            if shape.layer in ("signal", "pcb"):
+                layers.update(signal_layers)
+            elif shape.layer in layer_no:
+                layers.add(layer_no[shape.layer])
+        location = transform.dsn_to_board_point(via.x, via.y)
+        pad = _pad_tile(max(padstack.shapes, key=_shape_extent), transform)
+        box = pad.bounding_box()
+        drill = re.search(r"_([\d.]+):([\d.]+)_um", via.padstack)
+        drill_board = (
+            round(transform.dsn_to_board(float(drill.group(2)) * _DSN_PER_UM.get(dsn.unit, 1.0)))
+            if drill else 0
+        )
+        board.insert(
+            Via(
+                net_nos=[numbers[via.net]], fixed=True, padstack_name=via.padstack,
+                drill=drill_board, location=location, layers=sorted(layers or signal_layers),
+                shape=IntBox(box.ll.x + location.x, box.ll.y + location.y,
+                             box.ur.x + location.x, box.ur.y + location.y),
+            )
+        )
+
+
 def _insert_zones(dsn: DsnBoard, board: BasicBoard, transform: CoordinateTransform, nets) -> None:
     """Each DSN plane as a ConductionArea of its net on its layer."""
     layer_no = {layer.name: i for i, layer in enumerate(dsn.layers)}

src/freeroute/board/items.py

@@ -114,6 +114,11 @@ class Via(Item):
 
     padstack_name: str = ""
     location: IntPoint = field(default_factory=lambda: IntPoint(0, 0))
+    #: layer indices the via's pads occupy, and the largest pad as a box
+    layers: list[int] = field(default_factory=list)
+    shape: object = None
+    #: drill diameter in board units, when the padstack name gives it
+    drill: int = 0
 
 
 @dataclass

src/freeroute/board/search_tree.py

@@ -18,7 +18,7 @@ from __future__ import annotations
 
 from dataclasses import dataclass
 
-from freeroute.geometry import IntBox, Simplex, overlaps_2d, segment_octagon
+from freeroute.geometry import IntBox, IntPoint, Simplex, overlaps_2d, segment_octagon, segment_slab
 
 __all__ = ["TreeShape", "ShapeSearchTree"]
 
@@ -63,7 +63,9 @@ class TreeShape:
         segment swept by ``half_width + clearance`` (exact integer superset)."""
         if self.seg is None:
             return self.tile.offset(clearance)
-        a, b, half_width = self.seg
+        a, b, half_width = self.seg[-3:]
+        if self.seg[0] == "slab":  # a slanted pin exit, at any angle
+            return segment_slab(a, b, half_width + clearance)
         return segment_octagon(a, b, half_width + clearance)
 
 
@@ -151,6 +153,25 @@ class ShapeSearchTree:
                 return True
         return False
 
+    def segment_conflict(
+        self, a: IntPoint, b: IntPoint, half_width: int, net_no: int, layer: int,
+        clearance: int, kind: str = "wire",
+    ) -> bool:
+        """:meth:`clearance_conflict` for a slanted segment, checked on its
+        exact swept copper instead of its bounding box (which would reach the
+        neighbouring pads of a pin leaving along its turned pad's axis)."""
+        copper = segment_slab(a, b, half_width)
+        grown = segment_slab(a, b, half_width + clearance)
+        for shape in self.overlapping(grown.bounding_box()):
+            if shape.net_no == net_no or not shape.on_layer(layer):
+                continue
+            if shape.blocks != "all" and shape.blocks != kind + "s":
+                continue
+            other = shape.exact if shape.exact is not None else shape.tile
+            if overlaps_2d(copper if not shape.clearance else grown, other):
+                return True
+        return False
+
     def rule_area_overlap(self, box: IntBox, layer: int, kind: str = "wire") -> bool:
         """True if ``box`` overlaps a rule area on ``layer`` that stops ``kind``."""
         for shape in self.overlapping(box):
@@ -188,6 +209,8 @@ class ShapeSearchTree:
         overlap). Static pad-vs-pad spacing in the source design is not counted.
         """
         for shape in self.all_shapes():
+            if not shape.routed:
+                continue  # a pair with routed copper is checked from that side
             expanded = shape.tile.offset(clearance)
             grown = None  # exact clearance region, built lazily only for diagonals
             for other in self.overlapping(expanded):

src/freeroute/cli.py

@@ -30,8 +30,8 @@ from freeroute.ses import write_ses
 #: which optional flags each engine actually implements. Anything not listed for
 #: an engine is rejected by :func:`_validate` rather than quietly ignored.
 ENGINE_OPTIONS: dict[str, frozenset[str]] = {
-    "grid": frozenset({"rip_up", "max_passes", "seed", "orders", "promote", "access", "rollback"}),
+    "grid": frozenset({"rip_up", "max_passes", "seed", "orders", "promote", "access", "negotiate", "rollback"}),
-    "exact": frozenset({"shove", "diagonal", "rip_up", "max_passes", "seed", "orders", "promote", "access", "rollback"}),
+    "exact": frozenset({"shove", "diagonal", "rip_up", "max_passes", "seed", "orders", "promote", "access", "negotiate", "rollback"}),
     "room": frozenset({"shove", "pack"}),
 }
 
@@ -46,6 +46,7 @@ _FLAG_NAMES = {
     "orders": "--orders",
     "promote": "--promote-failures",
     "access": "--access-cost",
+    "negotiate": "--negotiate",
     "rollback": "--no-rollback",
 }
 
@@ -167,6 +168,14 @@ def build_parser() -> argparse.ArgumentParser:
         help="grid and exact engines: extra cost for a route to pass where it would close "
         "another pin's way out while that pin still has connections to route (default 0: off)",
     )
+    parser.add_argument(
+        "--negotiate",
+        type=int,
+        metavar="N",
+        help="grid and exact engines: before routing, N rounds of negotiation on the empty "
+        "board, where routes may share space at a price that rises where they compete; "
+        "the contested cells then cost extra in the real routing (default 0: off)",
+    )
     parser.add_argument(
         "--no-rollback",
         dest="rollback",
@@ -175,6 +184,14 @@ def build_parser() -> argparse.ArgumentParser:
         "connections a rip-up displaces are rerouted at once and the rip-up is undone "
         "if fewer connections end up routed",
     )
+    parser.add_argument(
+        "--hole-to-hole",
+        type=float,
+        default=0.25,
+        metavar="MM",
+        help="grid and exact engines: least distance between the edges of any two via "
+        "holes, of one net or two (KiCad's min_hole_to_hole; default 0.25)",
+    )
     parser.add_argument(
         "--jobs",
         type=int,
@@ -204,6 +221,7 @@ def main(argv: list[str] | None = None) -> int:
             ("orders", args.orders is not None),
             ("promote", args.promote_failures is not None),
             ("access", args.access_cost is not None),
+            ("negotiate", args.negotiate is not None),
             ("rollback", not args.rollback),
         )
         if asked
@@ -239,6 +257,8 @@ def main(argv: list[str] | None = None) -> int:
             "resolution": 2 if args.grid_resolution is None else args.grid_resolution,
             "heuristic_weight": args.heuristic_weight,
             "access_cost": args.access_cost or 0.0,
+            "negotiate": args.negotiate or 0,
+            "hole_to_hole_mm": args.hole_to_hole,
             "rollback": args.rollback,
         }
     elif args.engine == "grid":
@@ -249,6 +269,8 @@ def main(argv: list[str] | None = None) -> int:
             "edge_clearance_mm": args.edge_clearance,
             "resolution": 1 if args.grid_resolution is None else args.grid_resolution,
             "access_cost": args.access_cost or 0.0,
+            "negotiate": args.negotiate or 0,
+            "hole_to_hole_mm": args.hole_to_hole,
             "rollback": args.rollback,
         }
     if args.engine == "room":
@@ -287,6 +309,14 @@ def main(argv: list[str] | None = None) -> int:
         print(f"freeroute: {len(missing)} connection(s) not routed:", file=sys.stderr)
         for net, a, b, _zone in missing:
             print(f"  {net}: {a} to {b}", file=sys.stderr)
+    if result.narrowed:
+        print(
+            f"freeroute: {len(result.narrowed)} connection(s) of a wider net class only fitted "
+            "at the default width; their nets are written at the default width:",
+            file=sys.stderr,
+        )
+        for net, a, b in result.narrowed:
+            print(f"  {net}: {a} to {b}", file=sys.stderr)
     if in_zone:
         print(
             f"freeroute: {len(in_zone)} more connection(s) left to a zone fill that may join them:",

src/freeroute/dsn/model.py

@@ -27,6 +27,8 @@ __all__ = [
     "NetPin",
     "Net",
     "NetClass",
+    "WiringVia",
+    "WiringWire",
     "Keepout",
     "DsnBoard",
 ]
@@ -186,6 +188,26 @@ class Keepout:
     kind: str = "keepout"  # keepout | via_keepout | wire_keepout | place_keepout
 
 
+@dataclass
+class WiringWire:
+    """A track already on the board: ``(wire (path LAYER WIDTH x y ...) (net N))``."""
+
+    net: str
+    layer: str
+    width: float
+    coords: list[float] = field(default_factory=list)
+
+
+@dataclass
+class WiringVia:
+    """A via already on the board: ``(via PADSTACK x y (net N))``."""
+
+    net: str
+    padstack: str
+    x: float
+    y: float
+
+
 @dataclass
 class DsnBoard:
     """The fully parsed DSN file."""
@@ -197,6 +219,9 @@ class DsnBoard:
     layers: list[Layer] = field(default_factory=list)
     #: copper zones, as planes of a net
     planes: list[Plane] = field(default_factory=list)
+    #: copper already routed (the ``wiring`` scope), kept fixed
+    wires: list[WiringWire] = field(default_factory=list)
+    vias: list[WiringVia] = field(default_factory=list)
     #: bounding-box boundary shape (layer ``pcb``), if present
     boundary: Shape | None = None
     #: outline shapes (layer ``signal``)

src/freeroute/dsn/reader.py

@@ -27,6 +27,8 @@ from .model import (
     Pin,
     Resolution,
     WidthRule,
+    WiringVia,
+    WiringWire,
 )
 from .sexp import SExp, parse
 from .shapes import Shape, read_area, read_shape
@@ -531,11 +533,45 @@ def parse_dsn(text: str) -> DsnBoard:
             _read_placement(it, board)
         elif head == "network":
             _read_network(it, board)
-        # `wiring` and unknown scopes are intentionally ignored for now.
+        elif head == "wiring":
+            _read_wiring(it, board)
+        # unknown scopes are ignored
 
     return board
 
 
+def _read_wiring(node: SExp, board: DsnBoard) -> None:
+    """Tracks and vias already on the board. They stay where they are: the
+    router treats them as copper of their net that other nets keep clear of."""
+    for it in node.items:
+        if not isinstance(it, SExp):
+            continue
+        net_scope = it.child("net")
+        net = _first_value(net_scope) if net_scope is not None else None
+        if not net:
+            continue  # netless copper would need a keepout, not a wire
+        if it.head == "wire":
+            path = it.child("path") or it.child("polyline_path")
+            vals = [v.text for v in path.values()] if path is not None else []
+            if len(vals) < 6:
+                continue
+            try:
+                width = float(vals[1])
+                coords = [float(v) for v in vals[2:]]
+            except ValueError:
+                continue
+            board.wires.append(WiringWire(net=net, layer=vals[0], width=width, coords=coords))
+        elif it.head == "via":
+            vals = [v.text for v in it.values()]
+            if len(vals) < 3:
+                continue
+            try:
+                x, y = float(vals[1]), float(vals[2])
+            except ValueError:
+                continue
+            board.vias.append(WiringVia(net=net, padstack=vals[0], x=x, y=y))
+
+
 def _read_plane(node: SExp):
     """``(plane <net> (polygon <layer> <width> x y ...))`` -> :class:`Plane`."""
     from .model import Plane

src/freeroute/geometry/__init__.py

@@ -21,7 +21,7 @@ from .direction import Direction, IntDirection
 from .float_point import FloatPoint
 from .limits import CRIT_DOUBLE, CRIT_INT
 from .line import Line
-from .octagon import ceil_sqrt2, overlaps_2d, segment_octagon
+from .octagon import ceil_sqrt2, overlaps_2d, segment_octagon, segment_slab
 from .point import IntPoint, Point, RationalPoint, point, rational_point
 from .polygon import Polygon
 from .polygon_shape import PolygonShape
@@ -59,5 +59,6 @@ __all__ = [
     "shove_segment",
     "ceil_sqrt2",
     "segment_octagon",
+    "segment_slab",
     "overlaps_2d",
 ]

src/freeroute/geometry/octagon.py

@@ -29,7 +29,7 @@ from .line import Line
 from .point import IntPoint
 from .simplex import Simplex
 
-__all__ = ["ceil_sqrt2", "segment_octagon", "overlaps_2d"]
+__all__ = ["ceil_sqrt2", "segment_octagon", "segment_slab", "overlaps_2d"]
 
 
 def ceil_sqrt2(radius: int) -> int:
@@ -82,6 +82,46 @@ def segment_octagon(a: IntPoint, b: IntPoint, radius: int) -> Simplex:
     return Simplex.get_instance(lines)
 
 
+def segment_slab(a: IntPoint, b: IntPoint, radius: int) -> Simplex:
+    """Convex cover of segment ``a``-``b`` swept by ``radius``, at any angle.
+
+    The rectangle along the segment, ``radius`` either side, with flush ends
+    like :func:`polyline.segment_box`: the ends of a trace leg sit on a pad or
+    on the square corner tile of the next leg, which cover them. Corners are
+    rounded away from the middle and the radius gets one unit more, so the
+    side bounds never under-report, and it stays tight for a slanted segment
+    off the 45-degree lines (a pin leaving along its pad's axis on a part
+    turned 30 degrees).
+    """
+    dx, dy = b.x - a.x, b.y - a.y
+    length = math.hypot(dx, dy)
+    r = max(radius, 0) + 1
+    if length == 0:
+        return Simplex.from_corners([
+            IntPoint(a.x - r, a.y - r), IntPoint(a.x + r, a.y - r),
+            IntPoint(a.x + r, a.y + r), IntPoint(a.x - r, a.y + r),
+        ])
+    ux, uy = dx / length, dy / length
+    nx, ny = -uy, ux
+    mx, my = (a.x + b.x) / 2, (a.y + b.y) / 2
+
+    def out(x: float, y: float) -> IntPoint:
+        return IntPoint(math.ceil(x) if x >= mx else math.floor(x),
+                        math.ceil(y) if y >= my else math.floor(y))
+
+    corners = [
+        out(a.x + nx * r, a.y + ny * r),
+        out(b.x + nx * r, b.y + ny * r),
+        out(b.x - nx * r, b.y - ny * r),
+        out(a.x - nx * r, a.y - ny * r),
+    ]
+    for winding in (corners, corners[::-1]):
+        slab = Simplex.from_corners(winding)
+        if not slab.is_empty():
+            return slab
+    return Simplex(())
+
+
 def overlaps_2d(shape_a, shape_b) -> bool:
     """True if the two convex tiles share 2-D area (a real clearance overlap).
 

src/freeroute/route/exact_router.py

@@ -31,15 +31,17 @@ from dataclasses import dataclass, field
 import math
 
 from freeroute.board.board import BasicBoard
-from freeroute.board.items import Pin
+from freeroute.board.items import Pin, Via
 from freeroute.board.search_tree import ShapeSearchTree, TreeShape
 from freeroute.geometry import (
     IntBox,
     IntPoint,
     Polyline,
     PolylineShape,
+    Simplex,
     segment_box,
     segment_octagon,
+    segment_slab,
     shove_segment,
 )
 from freeroute.geometry.polyline import corner_box
@@ -98,7 +100,11 @@ def route_board_exact(
     seed: int | None = None,
     route_first: frozenset | None = None,
     access_cost: float = 0.0,
+    negotiate: int = 0,
     rollback: bool = True,
+    net_widths: dict[int, int] | None = None,
+    via_drill: int | None = None,
+    hole_to_hole: int = 0,
 ) -> ExactRouteResult:
     """Route ``board`` orthogonally and verify the result with exact geometry.
 
@@ -130,7 +136,11 @@ def route_board_exact(
         seed=seed,
         route_first=route_first,
         access_cost=access_cost,
+        negotiate=negotiate,
         rollback=rollback,
+        net_widths=net_widths,
+        via_drill=via_drill,
+        hole_to_hole=hole_to_hole,
     )
     edge = 0 if edge_clearance is None else edge_clearance
     outline = board.outline
@@ -148,7 +158,13 @@ def route_board_exact(
         net = pin.net_nos[0] if pin.net_nos else -1
         pin_layers = frozenset(layer for layer in pin.layers if layer in signal_layers)
         if pin_layers:
-            tree.insert(TreeShape(next(owner), net, pin_layers, box))
+            # a rotated pad is checked against its outline, not its box
+            exact = pin.shape if _is_rotated(pin.shape) else None
+            tree.insert(TreeShape(next(owner), net, pin_layers, box, exact=exact))
+    for net, copper_layers, box in board.get_fixed_copper():
+        on = frozenset(layer for layer in copper_layers if layer in signal_layers)
+        if on and not box.is_empty():
+            tree.insert(TreeShape(next(owner), net, on, box))
     for obstacle in board.get_obstacle_areas():
         if obstacle.layer not in signal_layers:
             continue
@@ -168,24 +184,40 @@ def route_board_exact(
 
     via_layers = frozenset(signal_layers)
     accepted: dict[int, _Accepted] = {}
+    fixed_vias = {
+        (item.net_nos[0], item.location)
+        for item in board.get_items()
+        if isinstance(item, Via) and item.fixed and item.net_nos
+    }
 
     # Verify connection by connection, so one conflicting segment of a
     # 25-pin supply net costs that one connection, not the whole net.
     rejected: list[tuple[int, str, str]] = []
     ends_list = result.connection_ends or [("?", "?", "")] * len(result.connections)
+    # each net is checked at the width it will be written at: its class's
+    # when all of its connections went in at that, else the default
+    net_half = dict(result.net_half)
     for (net_no, wires, vias), ends in sorted(
         zip(result.connections, ends_list, strict=False), key=lambda c: c[0][0]
     ):
-        boxes = _copper_boxes(wires, vias, half_width, via_layers, via_half)
+        wire_half = net_half.get(net_no, half_width)
-        wire_count = len(_copper_boxes(wires, [], half_width, via_layers, via_half))
+        pieces = _copper_pieces(wires, vias, wire_half, via_layers, via_half)
+        boxes = [(box, box_layers) for box, box_layers, _ in pieces]
+        wire_count = len(_copper_pieces(wires, [], wire_half, via_layers, via_half))
         if any(
-            tree.clearance_conflict(
+            (
-                box, net_no, layer, clearance, "wire" if i < wire_count else "via"
+                tree.segment_conflict(*seg, wire_half, net_no, layer, clearance)
+                if seg is not None
+                else tree.clearance_conflict(
+                    box, net_no, layer, clearance, "wire" if i < wire_count else "via"
+                )
             )
-            for i, (box, box_layers) in enumerate(boxes)
+            for i, (box, box_layers, seg) in enumerate(pieces)
             for layer in box_layers
-        ) or _end_in_rule_area(tree, wires, half_width) or (
+        ) or _end_in_rule_area(tree, wires, wire_half) or (
-            outline is not None and not all(outline.box_clear(b, edge) for b, _ in boxes)
+            outline is not None and not _inside_outline(
+                outline, boxes[:wire_count], vias, (via_half or wire_half) + edge, edge
+            )
         ):
             rejected.append((net_no, *ends))
             continue  # exact-clearance conflict -> drop (may be recovered by shove)
@@ -193,10 +225,21 @@ def route_board_exact(
         if acc is None:
             acc = accepted[net_no] = _Accepted(wires=[], vias=[])
         acc.wires.extend(wires)
-        acc.vias.extend(vias)
+        # connections of one net that end on the same plane cell share its
-        for box, box_layers in boxes:
+        # via: write it once, and never on top of a via already on the board
+        acc.vias.extend(
+            v for v in dict.fromkeys(vias)
+            if v not in acc.vias and not _on_fixed_via(net_no, v, fixed_vias, via_half)
+        )
+        for box, box_layers, seg in pieces:
             oid = next(owner)
-            tree.insert(TreeShape(oid, net_no, box_layers, box, routed=True))
+            if seg is None:
+                tree.insert(TreeShape(oid, net_no, box_layers, box, routed=True))
+            else:  # a slanted pin exit: its exact copper, rebuilt for the DRC check
+                tree.insert(TreeShape(
+                    oid, net_no, box_layers, box, routed=True,
+                    exact=segment_slab(*seg, wire_half), seg=("slab", *seg, wire_half),
+                ))
             acc.owners.append(oid)
 
     accepted_before_recovery = set(accepted)
@@ -243,6 +286,17 @@ def route_board_exact(
     for net_no, acc in accepted.items():
         clean.wires[net_no] = acc.wires
         clean.vias[net_no] = acc.vias
+    # shove and the diagonal pass lay copper at the default width: nets they
+    # recovered, and nets whose traces shove pushed aside
+    reshaped = (set(accepted) - accepted_before_recovery) | {
+        net for net, acc in accepted.items() if acc.shove_count
+    }
+    if diagonal:
+        reshaped = set(accepted)
+    clean.net_half = {
+        net: half for net, half in net_half.items() if net in accepted and net not in reshaped
+    }
+    clean.narrowed = list(result.narrowed)
 
     drc_clean = tree.has_violation(clearance) is None
     return ExactRouteResult(result=clean, tree=tree, drc_clean=drc_clean, shoves=shoves)
@@ -611,6 +665,36 @@ def _end_in_rule_area(tree, wires, half_width) -> bool:
     return False
 
 
+def _on_fixed_via(net_no, point, fixed_vias, via_half) -> bool:
+    """A routed via that reuses a via already on the board: the grid put it
+    on the fixed via's cell, a little off its centre, and it is not written."""
+    return any(
+        net == net_no and abs(loc.x - point.x) <= via_half and abs(loc.y - point.y) <= via_half
+        for net, loc in fixed_vias
+    )
+
+
+def _copper_pieces(wires, vias, half_width, via_layers, via_half=None):
+    """Like :func:`_copper_boxes`, but a slanted wire segment (a pin leaving
+    along a turned pad's axis) comes with its end points, so it can be checked
+    on its exact copper: ``(box, layers, (a, b) or None)``."""
+    via_half = via_half or half_width
+    pieces: list[tuple[IntBox, frozenset[int], tuple | None]] = []
+    for layer, points in wires:
+        on = frozenset({layer})
+        for a, b in zip(points, points[1:], strict=False):
+            if a.x == b.x or a.y == b.y:
+                pieces.append((segment_box(a, b, half_width), on, None))
+            else:
+                pieces.append((segment_slab(a, b, half_width).bounding_box(), on, (a, b)))
+        for c in points[1:-1]:
+            pieces.append((corner_box(c, half_width), on, None))
+    for loc in vias:
+        vbox = IntBox(loc.x - via_half, loc.y - via_half, loc.x + via_half, loc.y + via_half)
+        pieces.append((vbox, via_layers, None))
+    return pieces
+
+
 def _copper_boxes(wires, vias, half_width, via_layers, via_half=None):
     via_half = via_half or half_width
     boxes: list[tuple[IntBox, frozenset[int]]] = []
@@ -623,6 +707,19 @@ def _copper_boxes(wires, vias, half_width, via_layers, via_half=None):
     return boxes
 
 
+def _inside_outline(outline, wire_boxes, vias, via_reach, edge) -> bool:
+    """Copper inside the board, ``edge`` from its outline. A via is round, as
+    the grid and KiCad take it: its square box would reach past a chamfered
+    corner where the via itself does not."""
+    return all(outline.box_clear(b, edge) for b, _ in wire_boxes) and all(
+        outline.point_clear(v, via_reach) for v in vias
+    )
+
+
+def _is_rotated(shape) -> bool:
+    return isinstance(shape, Simplex) and not shape.is_int_box()
+
+
 def _net_pins(board: BasicBoard, net_no: int, signal_layers) -> list[Pin]:
     return [
         pin

src/freeroute/route/pipeline.py

@@ -12,6 +12,8 @@ to DSN units (dividing by the resolution) for the SES ``(wire (path ...))`` and
 
 from __future__ import annotations
 
+import re
+
 from freeroute.board import build_board
 from freeroute.dsn import DsnBoard, parse_dsn
 from freeroute.ses import RoutedVia, RoutedWire, RoutingResult, write_ses
@@ -34,6 +36,25 @@ def _rule_width_dsn(dsn: DsnBoard) -> float:
     return rules[0].value if rules else _DEFAULT_WIDTH_DSN
 
 
+def _net_widths_board(dsn: DsnBoard, scale: int) -> dict[int, int]:
+    """Track width of every net whose class asks for more than the default,
+    in board units, by net number (build_board numbers nets in DSN order)."""
+    default = _rule_width_dsn(dsn)
+    by_name: dict[str, float] = {}
+    for net_class in dsn.net_classes:
+        if not net_class.width_rules:
+            continue
+        width = net_class.width_rules[0].value
+        if width > default:
+            for name in net_class.net_names:
+                by_name[name] = max(by_name.get(name, 0.0), width)
+    return {
+        i + 1: round(by_name[net.name] * scale)
+        for i, net in enumerate(dsn.nets)
+        if net.name in by_name
+    }
+
+
 def _rule_clearance_dsn(dsn: DsnBoard) -> float:
     for rule in dsn.structure_rules.clearance_rules:
         if not rule.class_pairs:  # the layer-wide default clearance
@@ -53,6 +74,20 @@ def _mm_to_board(dsn: DsnBoard, scale: int, value_mm: float | None) -> int | Non
     return round(value_mm / unit_mm * scale)
 
 
+def _via_drill_board(dsn: DsnBoard, scale: int) -> int | None:
+    """The via's drill in board units, from KiCad's padstack name
+    (``Via[0-1]_600:300_um`` is a 600 um pad with a 300 um drill); None when
+    the name does not say, and the pad size stands in for it."""
+    match = re.search(r"_([\d.]+):([\d.]+)_um", _via_padstack(dsn))
+    if not match:
+        return None
+    return round(float(match.group(2)) * _dsn_units_per_um(dsn) * scale)
+
+
+def _dsn_units_per_um(dsn: DsnBoard) -> float:
+    return {"um": 1.0, "mm": 0.001, "mil": 1 / 25.4, "inch": 1 / 25400}.get(dsn.unit, 1.0)
+
+
 def _via_half_board(dsn: DsnBoard, scale: int) -> int | None:
     """Half the via pad's size in board units, from the DSN's via padstack.
 
@@ -83,6 +118,8 @@ def route_dsn_board(
     seed: int | None = None,
     route_first: frozenset | None = None,
     access_cost: float = 0.0,
+    negotiate: int = 0,
+    hole_to_hole_mm: float = 0.25,
     rollback: bool = True,
 ) -> tuple[RouteResult, int, list[str]]:
     """Route a parsed :class:`DsnBoard`; return the board-unit result, the scale,
@@ -107,7 +144,11 @@ def route_dsn_board(
         seed=seed,
         route_first=route_first,
         access_cost=access_cost,
+        negotiate=negotiate,
         rollback=rollback,
+        net_widths=_net_widths_board(dsn, scale),
+        via_drill=_via_drill_board(dsn, scale),
+        hole_to_hole=_mm_to_board(dsn, scale, hole_to_hole_mm) or 0,
     )
     return result, scale, [layer.name for layer in dsn.layers]
 
@@ -122,6 +163,9 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
     result = RoutingResult()
     for net_no, segments in route.wires.items():
         name = numbers_to_names.get(net_no, str(net_no))
+        # its class's width when every connection of the net went in at it
+        half = getattr(route, "net_half", {}).get(net_no)
+        net_width = 2 * half / scale if half else width_dsn
         for layer_index, path in segments:
             layer_name = layer_names[layer_index] if layer_index < len(layer_names) else "F.Cu"
             coords: list[float] = []
@@ -129,7 +173,7 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
                 coords.append(point.x / scale)
                 coords.append(point.y / scale)
             if len(coords) >= 4:
-                result.add_wire(name, RoutedWire(layer=layer_name, width=width_dsn, coords=coords))
+                result.add_wire(name, RoutedWire(layer=layer_name, width=net_width, coords=coords))
     for net_no, locations in route.vias.items():
         name = numbers_to_names.get(net_no, str(net_no))
         for loc in locations:
@@ -137,6 +181,9 @@ def _to_routing_result(route, dsn: DsnBoard, scale: int, layer_names: list[str])
     result.unrouted = [
         (numbers_to_names.get(n, str(n)), a, b, zone) for n, a, b, zone in getattr(route, "failed", [])
     ]
+    result.narrowed = [
+        (numbers_to_names.get(n, str(n)), a, b) for n, a, b in getattr(route, "narrowed", [])
+    ]
     return result
 
 
@@ -151,6 +198,8 @@ def build_routing_result(
     seed: int | None = None,
     route_first: frozenset | None = None,
     access_cost: float = 0.0,
+    negotiate: int = 0,
+    hole_to_hole_mm: float = 0.25,
     rollback: bool = True,
 ) -> RoutingResult:
     """Route ``dsn`` (grid track) and convert to a DSN-unit RoutingResult."""
@@ -159,6 +208,8 @@ def build_routing_result(
         edge_clearance_mm=edge_clearance_mm, resolution=resolution, seed=seed,
         route_first=route_first,
         access_cost=access_cost,
+        negotiate=negotiate,
+        hole_to_hole_mm=hole_to_hole_mm,
         rollback=rollback,
     )
     return _to_routing_result(route, dsn, scale, layer_names)
@@ -178,6 +229,8 @@ def route_dsn_board_exact(
     seed: int | None = None,
     route_first: frozenset | None = None,
     access_cost: float = 0.0,
+    negotiate: int = 0,
+    hole_to_hole_mm: float = 0.25,
     rollback: bool = True,
 ) -> tuple[ExactRouteResult, int, list[str]]:
     """Route a parsed :class:`DsnBoard` with the exact-geometry (orthogonal,
@@ -206,7 +259,11 @@ def route_dsn_board_exact(
         seed=seed,
         route_first=route_first,
         access_cost=access_cost,
+        negotiate=negotiate,
         rollback=rollback,
+        net_widths=_net_widths_board(dsn, scale),
+        via_drill=_via_drill_board(dsn, scale),
+        hole_to_hole=_mm_to_board(dsn, scale, hole_to_hole_mm) or 0,
     )
     return exact, scale, [layer.name for layer in dsn.layers]
 
@@ -225,6 +282,8 @@ def build_exact_routing_result(
     seed: int | None = None,
     route_first: frozenset | None = None,
     access_cost: float = 0.0,
+    negotiate: int = 0,
+    hole_to_hole_mm: float = 0.25,
     rollback: bool = True,
 ) -> RoutingResult:
     """Route ``dsn`` (exact track) and convert to a DSN-unit RoutingResult."""
@@ -241,6 +300,8 @@ def build_exact_routing_result(
         seed=seed,
         route_first=route_first,
         access_cost=access_cost,
+        negotiate=negotiate,
+        hole_to_hole_mm=hole_to_hole_mm,
         rollback=rollback,
     )
     return _to_routing_result(exact.result, dsn, scale, layer_names)

src/freeroute/route/room_router.py

@@ -515,6 +515,10 @@ def route_board_rooms(
         pin_layers = frozenset(layer for layer in pin.layers if layer in signal_layers)
         if pin_layers:
             tree.insert(TreeShape(next(owner), net, pin_layers, box))
+    for net, copper_layers, box in board.get_fixed_copper():
+        on = frozenset(layer for layer in copper_layers if layer in signal_layers)
+        if on and not box.is_empty():
+            tree.insert(TreeShape(next(owner), net, on, box))
     for obstacle in board.get_obstacle_areas():
         if obstacle.layer not in signal_layers:
             continue

src/freeroute/ses/model.py

@@ -60,6 +60,9 @@ class RoutingResult:
     #: connections the router could not make: (net name, one end, other end,
     #: the zone both ends sit in or "") -- a zone's fill may join the latter
     unrouted: list[tuple[str, str, str, str]] = field(default_factory=list)
+    #: connections of a wider net class that only fitted at the default width
+    #: (net name, one end, other end); their net is written at the default
+    narrowed: list[tuple[str, str, str]] = field(default_factory=list)
 
     def net(self, name: str, *, create: bool = False) -> RoutedNet | None:
         """Return the :class:`RoutedNet` with ``name`` (creating it if asked)."""

tests/route/test_axis_escapes.py

@@ -0,0 +1,113 @@
+"""Pins of a fine-pitch part turned off the grid axes leave along their pads.
+
+A QFN at 45 degrees has no straight exit: every horizontal or vertical step
+from a pin passes its neighbours closer than the clearance (0.35 mm away on
+each axis at 0.5 mm pitch). The grid leaves along the pad's own axis first,
+past the pin row, and the exact engine checks that slanted leg on its exact
+copper. Found on th-eda's lift ESC, where a QFN-24 at 45 degrees left 15
+connections unroutable on an empty board.
+"""
+
+from __future__ import annotations
+
+import math
+
+import pytest
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.geometry import IntPoint, overlaps_2d, segment_slab
+from freeroute.route.grid_router import GridRouter
+from freeroute.route.pipeline import (
+    _rule_clearance_dsn,
+    _rule_width_dsn,
+    _via_half_board,
+    build_exact_routing_result,
+)
+
+
+def _qfn_side_dsn(rotation: float) -> str:
+    """Two rows of five 0.25 x 0.8 mm pads at 0.5 mm pitch (one side of a
+    QFN and its opposite side), turned by ``rotation``; each pin of the top
+    row is its own net, routed to a pad 4.5 mm out, the pads fanned 1.5 mm
+    apart."""
+    cx, cy = 100000, -100000
+    t = math.radians(rotation)
+    out = (-math.sin(t), math.cos(t))  # the pads' outward axis after turning
+    along = (math.cos(t), math.sin(t))  # the pin row
+    pins, targets, nets = [], [], []
+    for i in range(5):
+        x = -1000 + 500 * i
+        pins += [f"(pin P {i + 1} {x} 1000)", f"(pin P {i + 6} {x} -1000)"]
+        px = cx + x * math.cos(t) - 1000 * math.sin(t)
+        py = cy + x * math.sin(t) + 1000 * math.cos(t)
+        spread = 1500 * (i - 2) - x  # fan the far pads out to 1.5 mm apart
+        tx = px + 4500 * out[0] + spread * along[0]
+        ty = py + 4500 * out[1] + spread * along[1]
+        targets.append(f"(place T{i + 1} {round(tx)} {round(ty)} front 0)")
+        nets.append(f"(net N{i} (pins U1-{i + 1} T{i + 1}-1))")
+    return f"""(pcb qfn (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  115000 -115000  85000 -115000  85000 -85000  115000 -85000
+      115000 -115000))
+    (via "Via[0-1]_450:200_um")
+    (rule (width 150) (clearance 150)))
+  (placement
+    (component Q (place U1 {cx} {cy} front {rotation}))
+    (component T {" ".join(targets)}))
+  (library
+    (image Q {" ".join(pins)})
+    (image T (pin t 1 0 0))
+    (padstack P (shape (rect F.Cu -125 -400 125 400)) (attach off))
+    (padstack t (shape (rect F.Cu -300 -300 300 300)) (attach off))
+    (padstack "Via[0-1]_450:200_um" (shape (circle F.Cu 450)) (shape (circle B.Cu 450))
+      (attach off)))
+  (network {" ".join(nets)}))"""
+
+
+@pytest.mark.parametrize("rotation", [45, 30, -45])
+def test_a_turned_fine_pitch_part_gets_its_pins_out(rotation):
+    result = build_exact_routing_result(parse_dsn(_qfn_side_dsn(rotation)), resolution=2, shove=True)
+    assert result.unrouted == []
+
+
+def test_the_exit_runs_along_the_pad_axis_and_clears_the_neighbours():
+    dsn = parse_dsn(_qfn_side_dsn(45))
+    s = dsn.resolution.value
+    board = build_board(dsn)
+    router = GridRouter(
+        board,
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        via_half=_via_half_board(dsn, s),
+        orthogonal=True,
+    )
+    pins = {p.name: p for p in board.get_pins() if p.component_ref == "U1"}
+    pin = pins["3"]
+    exit_point = router._axis_exit(pin)
+    assert exit_point is not None
+    dx, dy = exit_point.x - pin.location.x, exit_point.y - pin.location.y
+    assert abs(abs(dx) - abs(dy)) <= 2  # along the 45-degree axis
+    leg = segment_slab(pin.location, exit_point, router.half_width + router.clearance)
+    for name in ("2", "4"):
+        assert not overlaps_2d(leg, pins[name].shape)
+
+
+def test_a_pad_on_the_grid_axes_keeps_the_usual_exits():
+    dsn = parse_dsn(_qfn_side_dsn(0))
+    s = dsn.resolution.value
+    board = build_board(dsn)
+    router = GridRouter(board, trace_width=round(_rule_width_dsn(dsn) * s),
+                        clearance=round(_rule_clearance_dsn(dsn) * s), via_half=_via_half_board(dsn, s))
+    pin = next(p for p in board.get_pins() if p.component_ref == "U1" and p.name == "3")
+    assert router._axis_exit(pin) is None
+
+
+def test_a_slanted_slab_is_tight_where_a_bounding_box_is_not():
+    slab = segment_slab(IntPoint(0, 0), IntPoint(10000, 10000), 750)
+    # a point beside the diagonal but inside its bounding box
+    from freeroute.geometry import IntBox
+
+    assert not overlaps_2d(slab, IntBox(8000, 0, 8100, 100))
+    assert overlaps_2d(slab, IntBox(4900, 4900, 5100, 5100))

tests/route/test_fixed_wiring.py

@@ -0,0 +1,108 @@
+"""Tracks and vias already on the board (the DSN's wiring) are fixed copper."""
+
+from __future__ import annotations
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import route_dsn_board_exact
+
+_DSN = """(pcb wired (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  30000 0  30000 -20000  0 -20000  0 0))
+    (via "Via[0-1]_600:300_um") (rule (width 250) (clearance 200)))
+  (placement (component S (place A1 5000 -10000 front 0) (place A2 25000 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -400 -400 400 400)) (attach off))
+    (padstack "Via[0-1]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net SIG (pins A1-1 A2-1)) (net GND))
+  (wiring
+    (wire (path F.Cu 400  15000 0  15000 -20000) (net GND) (type route))
+    (via "Via[0-1]_600:300_um"  8000 -14000 (net GND) (type route))))"""
+
+
+def test_wiring_is_read_with_its_nets():
+    dsn = parse_dsn(_DSN)
+    assert [(w.net, w.layer, w.width) for w in dsn.wires] == [("GND", "F.Cu", 400.0)]
+    assert [(v.net, v.x, v.y) for v in dsn.vias] == [("GND", 8000.0, -14000.0)]
+
+
+def test_wiring_is_fixed_copper_and_not_a_connection_to_route():
+    board = build_board(parse_dsn(_DSN))
+    copper = board.get_fixed_copper()
+    gnd = next(n.net_number for n in board.nets if n.name == "GND")
+    assert copper and all(net == gnd for net, _, _ in copper)
+    assert not any(gnd in p.net_nos for p in board.get_pins())
+
+
+def test_other_nets_route_around_a_fixed_track():
+    dsn = parse_dsn(_DSN)
+    exact, scale, names = route_dsn_board_exact(dsn, resolution=2)
+    sig = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "SIG")
+    assert sig in exact.result.routed_net_numbers
+    assert exact.drc_clean
+    wall = 15000 * scale
+    for layer, pts in exact.result.wires.get(sig, []):
+        if names[layer] != "F.Cu":
+            continue
+        for p, q in zip(pts, pts[1:], strict=False):
+            assert not (min(p.x, q.x) < wall < max(p.x, q.x)), "crossed the GND track on F.Cu"
+
+
+# --- fixed wiring as connectivity ------------------------------------------
+
+_FANOUT = """(pcb fanout (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  30000 0  30000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  29500 -500  29500 -19500  500 -19500  500 -500))
+    (via "Via[0-3]_600:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 5000 -10000 front 0) (place A 10000 -10000 front 0)
+                          (place B 25000 -11500 back 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -300 -300 300 300)) (attach off))
+    (padstack "Via[0-3]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net GND (pins G1-1)) (net SIG (pins A-1 B-1)))
+  (wiring
+    (wire (path F.Cu 150  5000 -10000  5000 -11500) (net GND) (type route))
+    (via "Via[0-3]_600:300_um"  5000 -11500 (net GND) (type route))
+    (wire (path F.Cu 150  10000 -10000  10000 -11500) (net SIG) (type route))
+    (via "Via[0-3]_600:300_um"  10000 -11500 (net SIG) (type route))
+    (wire (path F.Cu 300  2000 -2000  8000 -2000) (net GND) (type route))))"""
+
+
+def test_a_pad_fanned_out_to_its_plane_needs_no_route():
+    dsn = parse_dsn(_FANOUT)
+    exact, _scale, _names = route_dsn_board_exact(dsn, resolution=2)
+    gnd = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "GND")
+    assert exact.result.failed == []
+    assert not exact.result.vias.get(gnd) and not exact.result.wires.get(gnd)
+
+
+def test_a_fanned_out_signal_is_routed_from_its_via():
+    # B is on the bottom face, level with A's fan-out via: starting from that
+    # via on B.Cu is the cheapest way, and needs no via of its own
+    dsn = parse_dsn(_FANOUT)
+    exact, scale, names = route_dsn_board_exact(dsn, resolution=2)
+    sig = next(i + 1 for i, n in enumerate(dsn.nets) if n.name == "SIG")
+    assert sig in exact.result.routed_net_numbers
+    assert not exact.result.vias.get(sig), "the fan-out via is already there"
+    assert {names[layer] for layer, _ in exact.result.wires[sig]} == {"B.Cu"}
+
+
+def test_the_session_never_repeats_copper_already_on_the_board():
+    # the JAR writes the DSN's wiring back into its session, and an applier
+    # then adds it a second time on top of itself; freeroute writes only
+    # what it routed
+    from freeroute.route.pipeline import build_exact_routing_result
+
+    fixed_vias = {(5000.0, -11500.0), (10000.0, -11500.0)}
+    fixed_paths = {(5000.0, -10000.0, 5000.0, -11500.0), (10000.0, -10000.0, 10000.0, -11500.0),
+                   (2000.0, -2000.0, 8000.0, -2000.0)}
+    result = build_exact_routing_result(parse_dsn(_FANOUT), resolution=2)
+    for net in result.nets:
+        assert not {(v.x, v.y) for v in net.vias} & fixed_vias
+        assert not {tuple(w.coords) for w in net.wires} & fixed_paths

tests/route/test_grid_exact_agreement.py

@@ -0,0 +1,284 @@
+"""The grid must not believe copper legal that the exact check then refuses.
+
+Each case is one way the two used to disagree on roomba-ESP12E: a rotated oval
+pad modelled as an inflated box (and opened to its own net), a via shared by
+two connections of a net losing its footprint when one of them is ripped, and
+a wider net class searched as if it were the default width.
+"""
+
+from __future__ import annotations
+
+import math
+
+import pytest
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.geometry import IntBox, Simplex
+from freeroute.route.grid_router import GridRouter
+from freeroute.route.pipeline import (
+    _rule_clearance_dsn,
+    _rule_width_dsn,
+    _via_half_board,
+    build_exact_routing_result,
+)
+
+# --- rotated oval pads -------------------------------------------------------
+
+
+def _socket_dsn(rotation: float, layout: str) -> str:
+    """A 1x4 2.54 mm socket strip (rect pin 1, oval pins 2-4) at ``rotation``,
+    each pin its own net, routed to a small SMD pad 0.9 mm away."""
+    cx, cy = 100000, -100000
+    t = math.radians(rotation)
+    ax = (math.cos(t), math.sin(t))
+    perp = (-math.sin(t), math.cos(t))
+    places = []
+    for i in range(4):
+        px, py = cx + 2540 * i * ax[0], cy + 2540 * i * ax[1]
+        side = 1 if i % 2 == 0 else -1
+        if layout == "y":
+            tx, ty = px, py + side * 9000
+        else:
+            tx, ty = px + side * 8000 * perp[0], py + side * 8000 * perp[1]
+        places.append(f"(place T{i + 1} {round(tx)} {round(ty)} front 0)")
+    nets = " ".join(f"(net N{i} (pins P3-{i + 1} T{i + 1}-1))" for i in range(4))
+    return f"""(pcb socket (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  125000 -115000  85000 -115000  85000 -75000  125000 -75000
+      125000 -115000))
+    (via "Via[0-1]_800:400_um")
+    (rule (width 300) (clearance 250)))
+  (placement
+    (component S (place P3 {cx} {cy} front {rotation}))
+    (component T {" ".join(places)}))
+  (library
+    (image S (pin R 1 0 0) (pin O 2 2540 0) (pin O 3 5080 0) (pin O 4 7620 0))
+    (image T (pin t 1 0 0))
+    (padstack O (shape (path F.Cu 1727.2 0 -152.4 0 152.4))
+      (shape (path B.Cu 1727.2 0 -152.4 0 152.4)) (attach off))
+    (padstack R (shape (rect F.Cu -863.6 -1016 863.6 1016))
+      (shape (rect B.Cu -863.6 -1016 863.6 1016)) (attach off))
+    (padstack t (shape (rect F.Cu -500 -500 500 500)) (attach off))
+    (padstack "Via[0-1]_800:400_um" (shape (circle F.Cu 800)) (shape (circle B.Cu 800))
+      (attach off)))
+  (network {nets}
+    (class c N0 N1 N2 N3 (circuit (use_via "Via[0-1]_800:400_um"))
+      (rule (width 300) (clearance 250)))))"""
+
+
+def test_a_rotated_oval_pad_is_its_outline_not_its_bounding_box():
+    board = build_board(parse_dsn(_socket_dsn(60, "y")))
+    oval = next(p for p in board.get_pins() if p.component_ref == "P3" and p.name == "2")
+    assert isinstance(oval.shape, Simplex) and not oval.shape.is_int_box()
+    box = oval.shape.bounding_box()
+    assert oval.shape.contains(oval.location)
+    assert not oval.shape.contains(box.ll) and not oval.shape.contains(box.ur)
+
+
+@pytest.mark.parametrize("layout", ["y", "perp"])
+def test_routes_leaving_a_rotated_socket_pass_the_exact_check(layout):
+    result = build_exact_routing_result(
+        parse_dsn(_socket_dsn(60, layout)), resolution=2, shove=True
+    )
+    assert result.unrouted == []
+
+
+# --- a via two connections share --------------------------------------------
+
+_SHARED_VIA = """(pcb shared (parser) (resolution um 10) (unit um)
+  (structure
+    (layer Top (type signal)) (layer Bottom (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (via "Via[0-1]_800:400_um")
+    (rule (width 300) (clearance 250)))
+  (library
+    (padstack p (shape (rect Top -400 -400 400 400)) (attach off))
+    (padstack "Via[0-1]_800:400_um" (shape (circle Top 800)) (shape (circle Bottom 800))
+      (attach off))
+    (image PAD (pin p 1 0 0)))
+  (placement (component PAD
+    (place G1 3000 -5000 front 0) (place G2 3000 -15000 front 0)
+    (place G3 17000 -10000 front 0) (place S1 3000 -10000 front 0)
+    (place S2 17000 -3000 front 0)))
+  (network (net GND (pins G1-1 G2-1 G3-1)) (net SIG (pins S1-1 S2-1))))"""
+
+
+def _line(a, b, layer):
+    (x, y), (x1, y1) = a, b
+    out = [(x, y, layer)]
+    while x != x1:
+        x += 1 if x1 > x else -1
+        out.append((x, y, layer))
+    while y != y1:
+        y += 1 if y1 > y else -1
+        out.append((x, y, layer))
+    return out
+
+
+def test_a_shared_via_keeps_its_footprint_when_one_user_is_ripped():
+    dsn = parse_dsn(_SHARED_VIA)
+    s = dsn.resolution.value
+    router = GridRouter(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        via_half=_via_half_board(dsn, s),
+    )
+    conns = router._conns = router._build_connections()
+    gnd = [c for c in conns if len({c.a.component_ref, c.b.component_ref} & {"G1", "G2", "G3"})]
+    sig = next(c for c in conns if c not in gnd)
+    first, second = gnd
+    g3 = router._cell_of(next(p for p in router.board.get_pins() if p.component_ref == "G3").location)
+    via = (g3[0] - 10, g3[1])
+
+    def through_via(conn):
+        a, b = router._cell_of(conn.a.location), router._cell_of(conn.b.location)
+        return _line(a, via, 0) + _line(via, b, 1)
+
+    router._commit(first, through_via(first))
+    router._commit(second, through_via(second))
+    footprint = [c for c in router._via_cells(via) if c != via]
+    router._rip(first)
+
+    assert second.routed and via in second.via_cells
+    assert all(router._via_claims.get(c) == [second.index] for c in footprint)
+    # another net still keeps its distance from the via that is left
+    assert all(router._enter_cost_base(c, 0, sig.net_no, False, conns) is None for c in footprint)
+
+
+def test_a_route_through_a_shared_via_rips_every_user():
+    """Two connections of a net share a via. Another net routed through it
+    in rip-up mode has to rip both, or the one left keeps its via under the
+    new trace and the exact check throws one of them out."""
+    dsn = parse_dsn(_SHARED_VIA)
+    s = dsn.resolution.value
+    router = GridRouter(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        via_half=_via_half_board(dsn, s),
+    )
+    conns = router._conns = router._build_connections()
+    gnd = [c for c in conns if len({c.a.component_ref, c.b.component_ref} & {"G1", "G2", "G3"})]
+    sig = next(c for c in conns if c not in gnd)
+    first, second = gnd
+    g3 = router._cell_of(next(p for p in router.board.get_pins() if p.component_ref == "G3").location)
+    via = (g3[0] - 10, g3[1])
+
+    def through_via(conn):
+        a, b = router._cell_of(conn.a.location), router._cell_of(conn.b.location)
+        return _line(a, via, 0) + _line(via, b, 1)
+
+    router._commit(first, through_via(first))
+    router._commit(second, through_via(second))
+    # the via's copper alone: footprint cells no trace or trace halo covers
+    crossing = [
+        node
+        for c in router._via_cells(via)
+        for node in ((*c, 0), (*c, 1))
+        if node not in router._cell_owner and node not in router._halo
+    ]
+    assert crossing
+
+    assert router._crossed_owners(crossing, sig.net_no, conns) == {first.index, second.index}
+
+
+# --- a wider net class --------------------------------------------------------
+
+_WIDE = """(pcb wide (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -10000  0 -10000  0 0))
+    (rule (width 300) (clearance 250)))
+  (placement (component S (place P1 2000 -5000 front 0) (place P2 18000 -5000 front 0)
+     (place Q1 10000 {ylo} front 0) (place Q2 10000 {yhi} front 0)
+     (place Q3 10000 -1000 front 0) (place Q4 10000 -9000 front 0)))
+  (library (image S (pin pad 1 0 0)) (padstack pad (shape (rect F.Cu -600 -600 600 600)) (attach off)))
+  (network (net PWR (pins P1-1 P2-1)) (net SIG (pins Q1-1 Q3-1)) (net SIG2 (pins Q2-1 Q4-1))
+    (class Power PWR (rule (width 500) (clearance 250)))))"""
+
+
+@pytest.mark.parametrize("resolution", [1, 2])
+@pytest.mark.parametrize("gap", [900, 1000, 1075])
+def test_a_wide_net_past_pads_it_does_not_fit_between_is_not_refused(gap, resolution):
+    # 0.3 mm fits the gap between the two pads, 0.5 mm does not: the grid
+    # must see that, rather than lay it wide and have the exact check drop it
+    ylo, yhi = -5000 - gap // 2 - 600, -5000 + gap // 2 + 600
+    result = build_exact_routing_result(
+        parse_dsn(_WIDE.format(ylo=ylo, yhi=yhi)), resolution=resolution
+    )
+    assert result.unrouted == []
+
+
+def _wide_router():
+    dsn = parse_dsn(_WIDE.format(ylo=-6050, yhi=-3950))
+    s = dsn.resolution.value
+    pwr = next(i for i, net in enumerate(dsn.nets, 1) if net.name == "PWR")
+    return GridRouter(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        resolution=2,
+        net_widths={pwr: 5000},
+    ), pwr
+
+
+def test_a_wide_trace_keeps_clear_of_a_default_one_at_the_grid_diagonal():
+    router, _pwr = _wide_router()
+    # 0.5 mm against 0.3 mm needs 0.25 + 0.25 + 0.15 = 0.65 mm between centres,
+    # on either axis, since the exact check compares boxes
+    need = 2500 + router.clearance + router.half_width
+    for dx, dy in [(2, 2), (2, 1), (1, 2)]:
+        assert max(dx, dy) * router.step < need
+        assert (dx, dy) in router._halo_for(2500)
+
+
+def test_a_wide_rip_up_route_counts_what_its_extra_width_crosses():
+    router, pwr_net = _wide_router()
+    conns = router._conns = router._build_connections()
+    pwr = next(c for c in conns if c.net_no == pwr_net)
+    other = next(c for c in conns if c.net_no != pwr_net)
+    # a default-width trace two cells from the wide route's path
+    x, y = 20, 5
+    router._commit(other, _line((x - 3, y + 2), (x + 3, y + 2), 0))
+    path = _line((x - 3, y), (x + 3, y), 0)
+    spread = router._spread_for(2500)
+    assert other.index not in router._crossed_owners(path, pwr.net_no, conns)
+    assert other.index in router._crossed_owners(path, pwr.net_no, conns, spread)
+
+
+def test_a_pad_cell_check_uses_the_rotated_outline():
+    board = build_board(parse_dsn(_socket_dsn(60, "y")))
+    router = GridRouter(board, trace_width=3000, clearance=2500, resolution=2)
+    oval = next(p for p in board.get_pins() if p.component_ref == "P3" and p.name == "2")
+    box = oval.shape.bounding_box()
+    margin = router.clearance + router.half_width
+    exact = set(router._pad_cells(oval.shape, box, margin))
+    boxed = set(router._cells_in_box(box, margin))
+    assert exact < boxed
+    for cell in boxed - exact:
+        c = router._cell_center(cell)
+        square = IntBox(c.x - margin, c.y - margin, c.x + margin, c.y + margin)
+        assert oval.shape.intersection(square).dimension() != 2
+
+
+def test_a_via_by_a_chamfered_corner_is_judged_round():
+    """The grid keeps a via's centre its radius plus the edge clearance from
+    the outline. The exact check used the via's square, whose corner reaches
+    past a 45-degree chamfer where the round via does not."""
+    from freeroute.board.outline import BoardOutline
+    from freeroute.geometry import IntBox, IntPoint
+    from freeroute.route.exact_router import _inside_outline
+
+    # a 10 mm square with its lower-left corner cut at 45 degrees
+    outline = BoardOutline([IntPoint(*p) for p in
+                            [(30, 0), (100, 0), (100, 100), (0, 100), (0, 30)]])
+    half, edge = 4, 1
+    via = IntPoint(19, 20)  # its centre 6.4 from the chamfer x + y = 30
+    square = IntBox(via.x - half, via.y - half, via.x + half, via.y + half)
+    assert not outline.box_clear(square, edge)  # the square's corner: 0.7 away
+    assert _inside_outline(outline, [], [via], half + edge, edge)
+    # 4.2 from the chamfer: the round via itself is too close
+    assert not _inside_outline(outline, [], [IntPoint(18, 18)], half + edge, edge)

tests/route/test_negotiate.py

@@ -0,0 +1,65 @@
+"""--negotiate: PathFinder-style rounds on the empty board before routing."""
+
+from __future__ import annotations
+
+from pathlib import Path
+
+import pytest
+
+from freeroute.board import build_board
+from freeroute.dsn import parse_dsn
+from freeroute.route.grid_router import GridRouter
+from freeroute.route.pipeline import _rule_clearance_dsn, _rule_width_dsn, route_dsn_board
+
+FIXTURES = Path(__file__).resolve().parent.parent / "dsn" / "fixtures"
+
+
+def _router(name, negotiate):
+    dsn = parse_dsn((FIXTURES / name).read_text())
+    s = dsn.resolution.value
+    return GridRouter(
+        build_board(dsn),
+        trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s),
+        negotiate=negotiate,
+    )
+
+
+def test_negotiation_leaves_the_board_empty_and_the_ends_as_they_were():
+    router = _router("true_density.dsn", 3)
+    conns = router._conns = router._build_connections()
+    ends = [(c.a_end, c.b_end) for c in conns]
+    router._negotiate(list(conns), conns)
+    assert router._history  # a dense board has contested cells
+    assert not router._cell_owner and not router._halo and not router._via_claims
+    assert not any(c.routed for c in conns)
+    assert [(c.a_end, c.b_end) for c in conns] == ends
+    assert router._present is None
+
+
+def test_sharing_is_priced_only_for_other_nets():
+    router = _router("true_density.dsn", 1)
+    node = (3, 4, 0)
+    router._history[node] = 2.0
+    router._present, router._present_cost = {node: {7: 1, 9: 2}}, 0.5
+    assert router._congestion(node, 7) == pytest.approx(2.5)  # one other net
+    assert router._congestion(node, 5) == pytest.approx(3.0)  # two other nets
+    router._present = None
+    assert router._congestion(node, 5) == pytest.approx(2.0)  # history only, after
+
+
+@pytest.mark.parametrize("name", ["ripup_needed.dsn", "true_density.dsn", "kicad_routable.dsn"])
+def test_negotiated_routing_keeps_the_occupancy_honest(name):
+    """Only routed connections hold cells afterwards, as without negotiation."""
+    router = _router(name, 3)
+    router.route()
+    conns = router._conns
+    assert all(conns[i].routed for i in router._cell_owner.values())
+    assert all(conns[i].routed for claims in router._halo.values() for i in claims)
+
+
+def test_option_reaches_the_router_and_is_off_by_default():
+    text = (FIXTURES / "kicad_routable.dsn").read_text()
+    plain, _, _ = route_dsn_board(parse_dsn(text))
+    again, _, _ = route_dsn_board(parse_dsn(text), negotiate=0)
+    assert plain.unrouted == again.unrouted

tests/route/test_net_widths.py

@@ -0,0 +1,42 @@
+"""Net classes wider than the default are routed at their width where it fits."""
+
+from __future__ import annotations
+
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import build_exact_routing_result
+
+_BOARD = """(pcb widths (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -10000  0 -10000  0 0))
+    {keepouts}
+    (rule (width 150) (clearance 150)))
+  (placement (component S (place P1 2000 -5000 front 0) (place P2 18000 -5000 front 0)))
+  (library (image S (pin pad 1 0 0)) (padstack pad (shape (rect F.Cu -600 -600 600 600)) (attach off)))
+  (network (net PWR (pins P1-1 P2-1))
+    (class Power PWR (rule (width 400) (clearance 150)))))"""
+
+# two keepouts leave a 0.65 mm channel: room for 0.15 mm (0.45), not for 0.4 mm (0.7)
+_CHANNEL = (
+    '(keepout "" (polygon F.Cu 0  9000 0  11000 0  11000 -4675  9000 -4675))\n'
+    '    (keepout "" (polygon F.Cu 0  9000 -5325  11000 -5325  11000 -10000  9000 -10000))'
+)
+
+
+def _route(keepouts=""):
+    return build_exact_routing_result(parse_dsn(_BOARD.format(keepouts=keepouts)), resolution=2)
+
+
+def test_a_wider_class_is_routed_and_written_at_its_width():
+    result = _route()
+    assert result.unrouted == [] and result.narrowed == []
+    widths = {w.width for net in result.nets for w in net.wires}
+    assert widths == {400.0}
+
+
+def test_a_wider_class_that_does_not_fit_falls_back_to_the_default():
+    result = _route(_CHANNEL)
+    assert result.unrouted == []
+    assert [net for net, _a, _b in result.narrowed] == ["PWR"]
+    widths = {w.width for net in result.nets for w in net.wires}
+    assert widths == {150.0}

tests/route/test_real_board_geometry.py

@@ -51,19 +51,22 @@ def test_routes_keep_edge_clearance_at_a_rounded_corner():
                 assert outline.edge_distance(p) >= half + 500 * scale - 1
 
 
-@pytest.mark.parametrize(("resolution", "escape"), [(1, 2), (4, 5)])
+@pytest.mark.parametrize("resolution", [1, 4])
-def test_every_pin_of_a_half_millimetre_pitch_row_escapes(resolution, escape):
+def test_every_pin_of_a_half_millimetre_pitch_row_escapes(resolution):
     # Five 0.3 mm pads at 0.5 mm pitch, each wired to its own pad 8 mm away.
     # Between two neighbours a trace's centre has a legal band only 0.15 mm
-    # wide. At resolution 1 the 0.4 mm grid misses most bands; at 4 its
+    # wide. At resolution 4 the 0.1 mm columns cannot miss it. At resolution
-    # 0.1 mm columns cannot, and every pin gets out, as the JAR manages.
+    # 1 the 0.4 mm grid misses most bands, but a stub leaves its pin straight
+    # along the band and jogs to the column only past the pads, so every pin
+    # gets out there too, as the JAR manages (only 2 did before).
     places = " ".join(f"(place R{i} {6000 + 500 * i} -6000 front 0)" for i in range(5))
     places += " " + " ".join(f"(place F{i} {6000 + 500 * i} -14000 front 0)" for i in range(5))
     nets = " ".join(f"(net N{i} (pins R{i}-1 F{i}-1))" for i in range(5))
     result, _, _ = route_dsn_board_exact(
         parse_dsn(_dsn(f"(component P {places})", nets)), resolution=resolution
     )
-    assert len(result.routed_net_numbers) == escape
+    assert len(result.routed_net_numbers) == 5
+    assert result.drc_clean
 
 
 def test_resolution_one_has_no_halo_so_the_grid_is_unchanged():
@@ -202,6 +205,18 @@ def test_smd_pads_reach_an_inner_plane_by_their_own_via():
     assert all(names[layer] in ("F.Cu", "B.Cu") for segs in result.result.wires.values() for layer, _ in segs)
 
 
+def test_a_pad_outside_the_plane_routes_to_it():
+    # G1 sits left of a plane that covers only the right half, so its route
+    # has to reach the plane's cells: those ends are the plane, not a pin
+    dsn_text = _four_layer_dsn().replace(
+        "(plane GND (polygon In1.Cu 0  500 -500  29500 -500  29500 -29500  500 -29500  500 -500))",
+        "(plane GND (polygon In1.Cu 0  15000 -500  29500 -500  29500 -29500  15000 -29500  15000 -500))",
+    )
+    result, _scale, _names = route_dsn_board_exact(parse_dsn(dsn_text))
+    gnd = next(i + 1 for i, n in enumerate(parse_dsn(dsn_text).nets) if n.name == "GND")
+    assert gnd in result.result.routed_net_numbers
+
+
 def test_a_through_hole_pad_inside_a_plane_needs_no_route():
     from freeroute.route.grid_router import _connected_groups
 
@@ -211,3 +226,29 @@ def test_a_through_hole_pad_inside_a_plane_needs_no_route():
     groups = _connected_groups(gnd_pins, plane, frozenset(id(z) for z in plane))
     hub = next(g for g in groups if g[1])
     assert [p.component_ref for p in hub[0]] == ["GT"]
+
+
+def test_a_pad_inside_a_via_keepout_reaches_the_plane_by_a_via_outside_it():
+    # a sensor's GND pad: vias are forbidden under the body, so the route
+    # has to leave on the top layer and drop to the plane past the keepout
+    dsn = parse_dsn("""(pcb repro (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  19500 -500  19500 -19500  500 -19500  500 -500))
+    (via_keepout "" (polygon signal 0  8500 -8500  11500 -8500  11500 -11500  8500 -11500  8500 -8500))
+    (via "Via[0-3]_600:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 10000 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -175 -300 175 300)) (attach off))
+    (padstack "Via[0-3]_600:300_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600)) (attach off)))
+  (network (net GND (pins G1-1))))""")
+    exact, scale, _names = route_dsn_board_exact(dsn, resolution=2)
+    assert exact.result.failed == []
+    (via,) = exact.result.vias[1]
+    half = 300 * scale  # the via's radius
+    outside = (via.x + half <= 8500 * scale or via.x - half >= 11500 * scale
+               or via.y - half >= -8500 * scale or via.y + half <= -11500 * scale)
+    assert outside, f"via at {via} is inside the via keepout"

tests/route/test_rollback.py

@@ -31,7 +31,7 @@ def test_occupancy_only_holds_routed_connections(name):
     router, _ = _routed_router(name)
     conns = router._conns
     assert all(conns[i].routed for i in router._cell_owner.values())
-    assert all(conns[i].routed for i in router._via_owner.values())
+    assert all(conns[i].routed for claims in router._via_claims.values() for i in claims)
     assert all(conns[i].routed for claims in router._halo.values() for i in claims)
 
 

tests/route/test_straight_pin_exits.py

@@ -0,0 +1,58 @@
+"""Pins of a 1.27 mm pitch row routed at 1.0 mm (the RN2483 module on the
+TTN Enschede mote). A trace centre has to stay within 0.06 mm of a pin's
+centreline to pass its neighbours, which no grid column hits, so a route
+leaves each pin straight along that line and only jogs to its column once
+past the pads. FreeRouting routes this row in full the same way."""
+
+from __future__ import annotations
+
+import pytest
+
+from freeroute.board import build_board
+from freeroute.board.items import Pin
+from freeroute.dsn import parse_dsn
+from freeroute.geometry import IntPoint
+from freeroute.route.grid_router import GridRouter
+from freeroute.route.pipeline import route_dsn_board_exact
+
+
+def _row(x0: int, pins: int = 6, skew: int = 3000) -> str:
+    places = " ".join(f"(place R{i} {x0 + 1270 * i} -5000 front 0)" for i in range(pins))
+    places += " " + " ".join(
+        f"(place T{i} {x0 + 1270 * i + skew} -15000 front 0)" for i in range(pins)
+    )
+    nets = " ".join(f"(net N{i} (pins R{i}-1 T{i}-1))" for i in range(pins))
+    return f"""(pcb t (parser) (resolution um 10) (unit um)
+  (structure (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0 0 0 30000 0 30000 -20000 0 -20000 0 0))
+    (via "Via[0-1]_600:400_um") (rule (width 1000) (clearance 200)))
+  (placement (component P {places}))
+  (library (image P (pin pad 1 0 0))
+    (padstack pad (shape (rect F.Cu -508 -762 508 762)) (attach off))
+    (padstack "Via[0-1]_600:400_um" (shape (circle F.Cu 600)) (shape (circle B.Cu 600))
+      (attach off)))
+  (network {nets}))"""
+
+
+@pytest.mark.parametrize("x0", [5000, 5150, 5300])
+def test_every_pin_of_a_row_leaves_straight_and_routes(x0):
+    # three offsets of the row against the grid; before, 2 or 3 of 6 routed
+    result, _, _ = route_dsn_board_exact(parse_dsn(_row(x0)), resolution=2)
+    assert len(result.routed_net_numbers) == 6
+    assert result.drc_clean
+
+
+def test_a_walled_in_pin_may_escape_to_the_column_either_side():
+    # two pins side by side leaving the same way can then jog apart
+    board = build_board(parse_dsn(_row(5000)))
+    router = GridRouter(board, trace_width=10000, clearance=2000, orthogonal=True, resolution=2)
+    router._conns = router._build_connections()
+    pin = next(
+        p for p in board.get_items()
+        if isinstance(p, Pin) and p.location == IntPoint(50000 + 2 * 12700, -50000)
+    )
+    net = pin.net_nos[0]
+    cx, cy = router._cell_of(pin.location)
+    nodes = router._escape_nodes(pin, net, router._conns, [0], (cx, cy))
+    columns = {x for x, y, _ in nodes if y != cy}
+    assert {cx - 1, cx, cx + 1} <= columns

tests/route/test_via_spacing.py

@@ -0,0 +1,136 @@
+"""Vias keep hole-to-hole spacing, even within one net."""
+
+from __future__ import annotations
+
+import itertools
+import math
+
+from freeroute.dsn import parse_dsn
+from freeroute.route.pipeline import route_dsn_board_exact
+
+# four GND pads 0.5 mm apart over a GND plane: each drops a via to the plane
+_DSN = """(pcb holes (parser) (resolution um 10) (unit um)
+  (structure
+    (layer F.Cu (type signal)) (layer In1.Cu (type power)) (layer In2.Cu (type power))
+    (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (plane GND (polygon In1.Cu 0  500 -500  19500 -500  19500 -19500  500 -19500  500 -500))
+    (via "Via[0-3]_500:300_um") (rule (width 150) (clearance 150)))
+  (placement (component S (place G1 9000 -10000 front 0) (place G2 9500 -10000 front 0)
+                          (place G3 10000 -10000 front 0) (place G4 10500 -10000 front 0)))
+  (library
+    (image S (pin smd 1 0 0))
+    (padstack smd (shape (rect F.Cu -150 -300 150 300)) (attach off))
+    (padstack "Via[0-3]_500:300_um" (shape (circle F.Cu 500)) (shape (circle B.Cu 500)) (attach off)))
+  (network (net GND (pins G1-1 G2-1 G3-1 G4-1))))"""
+
+
+def test_a_nets_own_vias_keep_hole_to_hole_spacing():
+    dsn = parse_dsn(_DSN)
+    exact, scale, _ = route_dsn_board_exact(dsn, resolution=2)
+    assert exact.result.failed == []
+    vias = exact.result.vias[1]
+    assert len(set(vias)) == len(vias), "a via written twice"
+    need = (300 + 250) * scale  # drill + 0.25 mm, centre to centre
+    for a, b in itertools.combinations(vias, 2):
+        assert math.hypot(a.x - b.x, a.y - b.y) >= need, f"vias at {a} and {b} too close"
+
+
+def test_connections_sharing_a_plane_via_write_it_once():
+    # eight GND pads 0.4 mm apart: the hole spacing makes several of them
+    # end on the same plane via, which must come out once, not once each
+    pads = " ".join(f"(place G{i} {9000 + 400 * i} -10000 front 0)" for i in range(8))
+    pins = " ".join(f"G{i}-1" for i in range(8))
+    dsn = parse_dsn(
+        _DSN.replace(
+            "(place G1 9000 -10000 front 0) (place G2 9500 -10000 front 0)\n"
+            "                          (place G3 10000 -10000 front 0) (place G4 10500 -10000 front 0)",
+            pads,
+        )
+        .replace("(pins G1-1 G2-1 G3-1 G4-1)", f"(pins {pins})")
+        .replace("(rect F.Cu -150 -300 150 300)", "(rect F.Cu -125 -300 125 300)")
+    )
+    exact, _scale, _ = route_dsn_board_exact(dsn, resolution=2)
+    vias = exact.result.vias[1]
+    assert len(vias) < 8, "no via is shared, so this board no longer tests sharing"
+    assert len(set(vias)) == len(vias), "a shared via written more than once"
+
+
+def _router(dsn_text, via_drill_um=300):
+    from freeroute.board import build_board
+    from freeroute.route.grid_router import GridRouter
+    from freeroute.route.pipeline import _rule_clearance_dsn, _rule_width_dsn
+
+    dsn = parse_dsn(dsn_text)
+    s = dsn.resolution.value
+    return GridRouter(
+        build_board(dsn), trace_width=round(_rule_width_dsn(dsn) * s),
+        clearance=round(_rule_clearance_dsn(dsn) * s), resolution=2, orthogonal=True,
+        via_drill=via_drill_um * s, hole_to_hole=250 * s,
+    ), s
+
+
+_THT = """(pcb tht (parser) (resolution um 10) (unit um)
+  (structure (layer F.Cu (type signal)) (layer B.Cu (type signal))
+    (boundary (path pcb 0  0 0  20000 0  20000 -20000  0 -20000  0 0))
+    (via "Via[0-1]_500:300_um") (rule (width 150) (clearance 150)))
+  (placement (component T (place J1 10000 -10000 front 0)))
+  (library (image T (pin tht 1 0 0))
+    (padstack tht (shape (circle F.Cu 1700)) (shape (circle B.Cu 1700)) (attach off))
+    (padstack "Via[0-1]_500:300_um" (shape (circle F.Cu 500)) (shape (circle B.Cu 500)) (attach off)))
+  (network (net SIG (pins J1-1))))"""
+
+
+def test_no_via_goes_near_a_through_hole_pads_hole_even_of_its_own_net():
+    router, s = _router(_THT)
+    pin = router._cell_of(router.board.get_pins()[0].location)
+    assert not router._holes_clear(pin, 1)  # own net, right on the pad
+    far = (pin[0] + 40, pin[1])
+    assert router._holes_clear(far, 1)
+
+
+def test_a_via_in_a_pad_keeps_hole_spacing_from_a_fixed_via():
+    from freeroute.geometry import IntPoint
+
+    text = _THT.replace("(network (net SIG (pins J1-1))))",
+                        "(network (net SIG (pins J1-1)))\n"
+                        "  (wiring (via \"Via[0-1]_500:300_um\"  3000 -3000 (net SIG) (type route))))")
+    router, s = _router(text)
+    assert not router._hole_clear_at(IntPoint(3400 * s, -3000 * s))  # 0.4 mm < 0.55 mm
+    assert router._hole_clear_at(IntPoint(3600 * s, -3000 * s))
+
+
+def test_hole_spacing_from_a_fixed_via_is_measured_from_where_it_really_is():
+    # a fixed via off the grid with its own 0.25 mm drill, and the router's
+    # via a smaller 0.2 mm one (the flight controller's case): a new via needs
+    # its centre 0.1 + 0.125 + 0.25 = 0.475 mm away, measured exactly, where
+    # one rule for all vias gave 0.2 + 0.25 = 0.45 from the cell centres
+    text = _THT.replace("(network (net SIG (pins J1-1))))",
+                        "(network (net SIG (pins J1-1)) (net GND))\n"
+                        "  (wiring (via \"Via[0-1]_500:250_um\"  3030 -3030 (net GND) (type route))))")
+    text = text.replace(
+        '(attach off)))\n  (network',
+        '(attach off))\n    (padstack "Via[0-1]_500:250_um" (shape (circle F.Cu 500)) '
+        '(shape (circle B.Cu 500)) (attach off)))\n  (network',
+    )
+    router, s = _router(text, via_drill_um=200)
+    via = next(v for v in router.board.get_items() if getattr(v, "drill", 0))
+    assert via.drill == 250 * s
+    loc = via.location
+    for cell in [(x, y) for x in range(router.cols) for y in range(router.rows)]:
+        c = router._cell_center(cell)
+        d = math.hypot(c.x - loc.x, c.y - loc.y)
+        if router.step * 1.5 < d < 470 * s:
+            assert not router._holes_clear(cell, 1), f"{d / s:.0f} um from the fixed via"
+        elif 560 * s < d < 700 * s and cell not in router._tht_block:
+            assert router._holes_clear(cell, 1)
+
+
+def test_a_route_keeps_its_own_vias_apart():
+    # a route that changed layer at (10, 10) may not change layer again one
+    # cell away; the same cell is the same through via, and far is fine
+    router, _s = _router(_THT)
+    came_from = {(10, 10, 1): (10, 10, 0), (11, 10, 1): (10, 10, 1), (12, 10, 1): (11, 10, 1)}
+    assert router._near_path_via((12, 10, 1), (11, 10), came_from)
+    assert not router._near_path_via((12, 10, 1), (10, 10), came_from)
+    assert not router._near_path_via((12, 10, 1), (40, 10), came_from)

tests/test_cli.py

@@ -158,6 +158,7 @@ def test_cli_supported_combinations_are_accepted(tmp_path):
         "orders": ["--orders", "2"],
         "promote": ["--promote-failures", "2"],
         "access": ["--access-cost", "5"],
+        "negotiate": ["--negotiate", "2"],
         "rollback": ["--no-rollback"],
     }
     for engine, options in ENGINE_OPTIONS.items():